Команда layer в автокаде
AutoCAD 2016, AutoCAD Architecture 2016, AutoCAD Civil 3D 2016, AutoCAD Electrical 2016, AutoCAD MEP 2016, AutoCAD Map 3D 2016, AutoCAD Mechanical 2016, AutoCAD P&ID 2016, AutoCAD Plant 3D 2016, AutoCAD Structural Detailing 2016, & AutoCAD Utility Design 2016
By:
Manages layers and layer properties.
The following prompts are displayed.
?—List Layers
Displays a list of the currently defined layers, showing their names, states, color numbers, linetypes, lineweights, and whether they are externally dependent layers.
Creates a layer and makes it current. New objects are drawn on the current layer.
If no layer exists for the name you enter, a new layer with that name is created. The new layer is on and assumes the following properties by default: color number 7, the CONTINUOUS linetype, and a lineweight of DEFAULT.
If the layer exists but is turned off, it is turned on.
Specifies a new current layer but does not create the layer if it does not already exist. If the layer exists but is turned off, it is turned on and made current. A frozen layer cannot be made current.
Creates layers. You can create two or more layers by entering names separated by commas.
Rename
Renames an existing layer.
Makes selected layers visible and available for plotting.
Makes selected layers invisible and excludes them from plotting.
Color
Changes the color associated with a layer. Enter a color name or a number from 1 through 255.
Specifies a true color to be used for the selected object. Enter three integer values from 0 to 255 separated by commas to specify a true color.
Specifies a color from a loaded color book, guide, or set to use for the selected object. Enter the name of a color book that has been installed, such as "DIC COLOR GUIDE(R)$DIC 43".
The color is assigned to the layer or layers, and the layers are turned on. To assign a color but turn off the layer, precede the color with a minus sign (-).
Ltype
Changes the linetype associated with a layer.
Lweight
Changes the lineweight associated with a layer.
If you enter a valid lineweight, the current lineweight is set to the new value. If you enter a lineweight that is not valid, the current lineweight is set to the nearest fixed lineweight value. If you would like to plot an object with a custom width not found in the list of fixed lineweight values, you can use the Plot Style Table Editor to customize plotted lineweights.
Transparency
Changes the transparency level associated with a layer. Enter a value from 0 to 90.
After specifying a transparency value, the following prompt is displayed:
Enter name list of layer(s) for transparency specified value% : Enter the names of the layers to which to apply this transparency level, or press Enter to apply it to the current layer only
Material
Attaches a material to a layer. The material must be available in the drawing before it can be assigned to a layer.
Controls whether visible layers are plotted. If a layer is set to plot but is currently frozen or turned off, the layer is not plotted.
Pstyle
Sets the plot style assigned to a layer.
Note: The Pstyle option is available only when you are using named plot styles. (The PSTYLEPOLCY system variable is set to 0.)
If you select a plot style other than NORMAL, the following prompt is displayed:
Enter name list of layer(s) for plot style current : Enter the names of the layers to use this plot style, or press Enter to apply the style to the current layer only
Freeze
Freezes layers, making them invisible and excluding them from regeneration and plotting.
Thaws frozen layers, making them visible and available for regeneration and plotting.
Locks layers, preventing editing of objects on those layers.
Unlock
Unlocks selected locked layers, permitting editing of objects on those layers.
State
Saves and restores the state and property settings of the layers in a drawing.
?—List Named Layer States
Lists the named layer state (LAS) files in the support path for the drawing.
Saves the state and properties settings of the layers in a drawing under a specified layer state name. When saving a layer state, you specify which layer settings are affected when the layer state is later restored.
Restores the state and property settings of all layers to previously saved settings. Restores only those layer state and property settings that were selected when the layer state was saved.
Changes the saved layer settings for a specified layer state. When the layer state is restored, the specified settings are used.
Changes the name of a saved layer state.
Removes a saved layer state.
Loads a previously exported layer state (LAS) file, or layers states from a file (DWG, DWS, DWT) into the current drawing. Additional layers may be created as a result of importing a layer state file.
Saves a selected named layer state to a layer state (LAS) file.
Description
Sets the description property value of the existing layer.
A warning prompt is displayed when you enter a description to a layer with an existing description.
By:
Manages layers and layer properties.
The following prompts are displayed.
?—List Layers
Displays a list of the currently defined layers, showing their names, states, color numbers, linetypes, lineweights, and whether they are externally dependent layers.
Creates a layer and makes it current. New objects are drawn on the current layer.
If no layer exists for the name you enter, a new layer with that name is created. The new layer is on and assumes the following properties by default: color number 7, the CONTINUOUS linetype, and a lineweight of DEFAULT.
If the layer exists but is turned off, it is turned on.
Specifies a new current layer but does not create the layer if it does not already exist. If the layer exists but is turned off, it is turned on and made current. A frozen layer cannot be made current.
Creates layers. You can create two or more layers by entering names separated by commas.
Rename
Renames an existing layer.
Makes selected layers visible and available for plotting.
Makes selected layers invisible and excludes them from plotting.
Color
Changes the color associated with a layer. Enter a color name or a number from 1 through 255.
Specifies a true color to be used for the selected object. Enter three integer values from 0 to 255 separated by commas to specify a true color.
Specifies a color from a loaded color book, guide, or set to use for the selected object. Enter the name of a color book that has been installed, such as "DIC COLOR GUIDE(R)$DIC 43".
The color is assigned to the layer or layers, and the layers are turned on. To assign a color but turn off the layer, precede the color with a minus sign (-).
Ltype
Changes the linetype associated with a layer.
Lweight
Changes the lineweight associated with a layer.
If you enter a valid lineweight, the current lineweight is set to the new value. If you enter a lineweight that is not valid, the current lineweight is set to the nearest fixed lineweight value. If you would like to plot an object with a custom width not found in the list of fixed lineweight values, you can use the Plot Style Table Editor to customize plotted lineweights.
Transparency
Changes the transparency level associated with a layer. Enter a value from 0 to 90.
After specifying a transparency value, the following prompt is displayed:
Enter name list of layer(s) for transparency specified value% : Enter the names of the layers to which to apply this transparency level, or press Enter to apply it to the current layer only
Material
Attaches a material to a layer. The material must be available in the drawing before it can be assigned to a layer.
Controls whether visible layers are plotted. If a layer is set to plot but is currently frozen or turned off, the layer is not plotted.
Pstyle
Sets the plot style assigned to a layer.
Note: The Pstyle option is available only when you are using named plot styles. (The PSTYLEPOLCY system variable is set to 0.)
If you select a plot style other than NORMAL, the following prompt is displayed:
Enter name list of layer(s) for plot style current : Enter the names of the layers to use this plot style, or press Enter to apply the style to the current layer only
Freeze
Freezes layers, making them invisible and excluding them from regeneration and plotting.
Thaws frozen layers, making them visible and available for regeneration and plotting.
Locks layers, preventing editing of objects on those layers.
Unlock
Unlocks selected locked layers, permitting editing of objects on those layers.
State
Saves and restores the state and property settings of the layers in a drawing.
?—List Named Layer States
Lists the named layer state (LAS) files in the support path for the drawing.
Saves the state and properties settings of the layers in a drawing under a specified layer state name. When saving a layer state, you specify which layer settings are affected when the layer state is later restored.
Restores the state and property settings of all layers to previously saved settings. Restores only those layer state and property settings that were selected when the layer state was saved.
Changes the saved layer settings for a specified layer state. When the layer state is restored, the specified settings are used.
Changes the name of a saved layer state.
Removes a saved layer state.
Loads a previously exported layer state (LAS) file, or layers states from a file (DWG, DWS, DWT) into the current drawing. Additional layers may be created as a result of importing a layer state file.
Saves a selected named layer state to a layer state (LAS) file.
Description
Sets the description property value of the existing layer.
A warning prompt is displayed when you enter a description to a layer with an existing description.
Reconcile
Sets the unreconciled property of an unreconciled layer.
? - Name List of Layers
Displays a list of all unreconciled layers.
Resets the xref layer property override in the current drawing to the layer settings in the xref.
- On
- Color
- Linetype
- Lineweight
- Transparency
- Plot
- Freeze
- Lock
- New VP Freeze
- Description
- All
After specifying the xref layer property or all properties, the following prompt is displayed:
Enter xref layer name(s) to reset or [?] or : Enter the names of the xref layer (or multiple layers separated by comma) to reset, or press Enter to reset all xref layers. ? - Name List of Xref Layers
Создание сложных чертежей связано с размещением на чертеже большого количества графических примитивов, выполнением штриховки, нанесением размеров, размещением текста.
Каждый из этих объектов имеет определенные свойства: цвет, вес (толщину) линии, тип линий и т.д.
Назначение и использование слоев
Система автоматизированного проектирования AutoCad предоставляет в распоряжение пользователю инструмент — Layer (Слой), что позволяет компоновать объекты с однотипными свойствами вместе. Объекты различного типа целесообразно размещать на разных слоях. Каждый из графических примитивов наряду с другими свойствами имеет и такую. как Layer — слой, которому он принадлежит. Слои можно представить как прозрачные кальки, на каждой из которых созданы те или иные элементы чертежа. При наложении они образуют сложный чертеж. Для объектов одного слоя можно задавать свойства глобально для всего слоя (ByLayer — по слою) и локально для отдельных объектов.
Слой также является объектом, поэтому имеет присущие ему свойства. Каждый чертеж автоматически содержит слой Layer 0. Его можно удалить, но можно изменить свойства. Создание других слоев возлагается на пользователя. Управление слоями осуществляется через диалоговое окно Layer Properties Manager, которое вызывается командой меню Format ? Layer или кнопками панели инструментов Layer.
Свойства слоев
В каждый момент времени текущим может быть только один слой. Чертежи новых графических примитивов происходит на текущем слое. Для выполнения редактирование объектов не обязательно, чтобы слой был текущим.
Список созданных слоев отображается в окне Layer Properties. Каждый из слоев имеет следующие свойства:
Имя ( Name ) | Имя слоя. Щелкнув на имени, можно выбрать слой для определения его свойств или сделать его текущим. |
Вкл .( On \ Off ) | Включить \ выключить. Если выключить слой, то объекты, размещенные на нем, не отображаются на экране и не распечатываются. Их нельзя редактировать. Исключением является команда Erase ( All ). |
Заморозить( Freeze \ Thaw ) | Заморозить \ разморозить. Объекты замороженного слоя не отражаются ??на экране и не распечатываются. Их нельзя редактировать. Эта особенность имеет более высокий приоритет, нежели ВЫКЛ., замороженные слои со свойством ВЫКЛ. Не отображаются на экране. |
Блокирован( Lock \ Unlock ) | Заблокировать \ разблокировать. Объекты на заблокированных слоях остаются видимыми. Их можно распечатывать, но нельзя редактировать. |
Цвет ( Color ) | Цвет. Выбирается цвет объектов, принадлежащих данному слою. |
( Linetype ) | Тип линий |
Штрихи( Lineweight ) | Вес ( толщина) линий слоя. |
Стиль печати | Назначение стиля печати. |
Печать | Разрешается \ запрещается печатание слоя . |
Создание слоя
Создать новый слой можно, нажав кнопку New Layer в диалоговом окне Layer Properties Manager. Имя нового слоя со стандартным именем Layer1 ( Layer2 … , LayerN ) появится в списке слоев. Сразу же можно переименовать слой. Имя не должно содержать более 256 символов, и в имени не допускаются пробелы. Имя слоя можно изменить, дважды щелкнув на нем мышью. Созданный слой будет иметь свойства: цвет White, тип линий Continuous и вес линий Default.
Свойства слоя можно изменить. Нажмите Детали и в нижней части диалогового окна появятся поля для выбора значений параметров.
Цвет слоя
Цвет выбирается в строке слоя, нажав мышку на поле Color. Появляется окно Select Color, в котором представлена палитра цветов. Другой способ выбрать цвет из списка на палитре Properties.
Вес (толщина ) линий слоя
Различные элементы чертежа при выводе на печать могут иметь разный вес линий.
Осуществить выбор необходимого значения можно в окне Lineweight style, что появляется при нажатии мыши в строке слоя на поле Lineweight или из списка с соответствующим именем на палитре Properties.
Тип линий слоя
Тип линий выбирается также двумя способами — нажатием мышки на соответствующем поле в строке слоя или из списка в палитре Properties. Если же нужный тип линий отсутствует, его нужно подгрузить. Для этого нажать в окне Select Linetype кнопку Open и в окне Load or Reload Linetype выберите нужные. Чтобы выбрать типы линий, содержащихся в списка в произвольном порядке, удерживайте нажатой клавишу Ctrl. Если же нужно выбрать типы линий, которые расположены рядом, зажмите клавишу Shift и нажмите мышь на имени первого и последнего типа. Затем нажмите ОК .
Скачав у нас на сайте в теме «Набор типов линий для AutoCAD» архив с набором типов линий и теперь хотите ими пользоваться, но возникает вопрос: что с этими файлами в формате LIN делать, как их добавить в AutoCAD? Об этом мы сейчас Вам расскажем.
Берем файлы с типами линий (они состоят из трех фалов с расширением *.LIN *.SHP *.SHX) и копируем их в папку Support программы AutoCAD (или AutoCAD Civil3D, AutoCAD Architecture, AutoCAD Mechanical и т.п.) на Вашем компьютере (например: C:\Program Files\Autodesk\AutoCAD ****\Support). Для удобства можно создать отдельную папку, например Линии.
Затем, запускаем программу AutoCAD и переходим в меню Настройка на вкладку Файлы.
В окне Пути доступа, имена файлов и папки выделяем первую строку с названием Путь доступа к вспомогательным файлам и нажимаем на кнопку Добавить, а затем кнопку Обзор. Указываем путь к созданной нами ранее папке Линии нажимаем OK.
У Вас появиться строка с указанием пути доступа к папке Линии. Нажимаем на кнопку Применить и OK.
Теперь открываем окно Диспетчер типов линий. Открыть данное можно следующими способами:
В окне Диспетчер типов линий кликаем на кнопку Загрузить…
В появившемся окне Загрузка/перегрузка типов линий кликаем на кнопку Файл…
Указываем путь к нашему типу линий и открываем этот тип в формате *.LIN.
Теперь в окне Доступные типы линий выбираем нужную Вам линию и нажимаем OK.
Также закрываем окно Диспетчер типов линий нажатием кнопки OK.
На вкладке Свойства кликаем на развертывающийся список возле типа линий и выбираем нашу линию и
рисуем нашу линию с заданным типом.
Прочитав статью Вы узнали, как добавить штриховки в AutoCAD и когда Вам пришлют архив с чертежами, в котором помимо самих чертежей будут находиться файлы типов линий — будете знать что с ними делать.
By:
Manages layers and layer properties.
The following prompts are displayed.
?—List Layers
Displays a list of the currently defined layers, showing their names, states, color numbers, linetypes, lineweights, and whether they are externally dependent layers.
Creates a layer and makes it current. New objects are drawn on the current layer.
If no layer exists for the name you enter, a new layer with that name is created. The new layer is on and assumes the following properties by default: color number 7, the CONTINUOUS linetype, and a lineweight of DEFAULT.
If the layer exists but is turned off, it is turned on.
Specifies a new current layer but does not create the layer if it does not already exist. If the layer exists but is turned off, it is turned on and made current. A frozen layer cannot be made current.
Creates layers. You can create two or more layers by entering names separated by commas.
Rename
Renames an existing layer.
Makes selected layers visible and available for plotting.
Makes selected layers invisible and excludes them from plotting.
Color
Changes the color associated with a layer. Enter a color name or a number from 1 through 255.
Specifies a true color to be used for the selected object. Enter three integer values from 0 to 255 separated by commas to specify a true color.
Specifies a color from a loaded color book, guide, or set to use for the selected object. Enter the name of a color book that has been installed, such as "DIC COLOR GUIDE(R)$DIC 43".
The color is assigned to the layer or layers, and the layers are turned on. To assign a color but turn off the layer, precede the color with a minus sign (-).
Ltype
Changes the linetype associated with a layer.
Lweight
Changes the lineweight associated with a layer.
If you enter a valid lineweight, the current lineweight is set to the new value. If you enter a lineweight that is not valid, the current lineweight is set to the nearest fixed lineweight value. If you would like to plot an object with a custom width not found in the list of fixed lineweight values, you can use the Plot Style Table Editor to customize plotted lineweights.
Transparency
Changes the transparency level associated with a layer. Enter a value from 0 to 90.
After specifying a transparency value, the following prompt is displayed:
Enter name list of layer(s) for transparency specified value% : Enter the names of the layers to which to apply this transparency level, or press Enter to apply it to the current layer only
Material
Attaches a material to a layer. The material must be available in the drawing before it can be assigned to a layer.
Controls whether visible layers are plotted. If a layer is set to plot but is currently frozen or turned off, the layer is not plotted.
Pstyle
Sets the plot style assigned to a layer.
Note: The Pstyle option is available only when you are using named plot styles. (The PSTYLEPOLCY system variable is set to 0.)
If you select a plot style other than NORMAL, the following prompt is displayed:
Enter name list of layer(s) for plot style current : Enter the names of the layers to use this plot style, or press Enter to apply the style to the current layer only
Freeze
Freezes layers, making them invisible and excluding them from regeneration and plotting.
Thaws frozen layers, making them visible and available for regeneration and plotting.
Locks layers, preventing editing of objects on those layers.
Unlock
Unlocks selected locked layers, permitting editing of objects on those layers.
State
Saves and restores the state and property settings of the layers in a drawing.
?—List Named Layer States
Lists the named layer state (LAS) files in the support path for the drawing.
Saves the state and properties settings of the layers in a drawing under a specified layer state name. When saving a layer state, you specify which layer settings are affected when the layer state is later restored.
Restores the state and property settings of all layers to previously saved settings. Restores only those layer state and property settings that were selected when the layer state was saved.
Changes the saved layer settings for a specified layer state. When the layer state is restored, the specified settings are used.
Changes the name of a saved layer state.
Removes a saved layer state.
Loads a previously exported layer state (LAS) file, or layers states from a file (DWG, DWS, DWT) into the current drawing. Additional layers may be created as a result of importing a layer state file.
Saves a selected named layer state to a layer state (LAS) file.
Description
Sets the description property value of the existing layer.
A warning prompt is displayed when you enter a description to a layer with an existing description.
Reconcile
Sets the unreconciled property of an unreconciled layer.
? - Name List of Layers
Displays a list of all unreconciled layers.
Resets the xref layer property override in the current drawing to the layer settings in the xref.
- On
- Color
- Linetype
- Lineweight
- Transparency
- Plot
- Freeze
- Lock
- New VP Freeze
- Description
- All
After specifying the xref layer property or all properties, the following prompt is displayed:
Enter xref layer name(s) to reset or [?] or : Enter the names of the xref layer (or multiple layers separated by comma) to reset, or press Enter to reset all xref layers. ? - Name List of Xref Layers
Читайте также: