Настройка модема zyxel u336s
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.
Note: Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind or character to the purchaser.
To obtain the services of this warranty, please contact ZyXEL’s Service Center, refer to the separate Warranty Card for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid (USA and territories only). If the customer desires some other return destination beyond the U.S. borders, the customer shall bear the cost of the return shipment. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
Copyright ©1997 by ZyXEL
The contents of this book may not be reproduced (in any part or as a whole) or transmitted in any form or by any means without the written permission of the publisher.
Published by ZyXEL Communications Corporation. All rights reserved.
Note: ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patents rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This document is subject to change without notice.
Trademarks mentioned in this manual are used for informational purposes only.
Trademarks are properties of their respective owners.
FCC Part 15 Information
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operations.
This equipment has been tested and found to comply with the limits for a CLASS A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
∙ Reorient or relocate the receiving antenna.
∙ Increase the separation between the equipment and the receiver.
∙ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
∙ Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded RS-232 cables are required to be used to ensure compliance with FCC Part 15, and it is the responsibility of the user to provide and use shielded RS-232 cables.
Information for Canadian Users
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Industry Canada does not guarantee that the equipment will operate to a user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the
company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly. The customer should be aware that the compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
For their own protection, users should ensure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.
This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry Canada. The declarations of CE marking:
This product has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I.420. This product complies with the following directives:
1. The Council Directive 89/336/EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility. (EMC Directive)
2. Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecommunication terminal equipment. (The Telecom Terminal Equipment Directive)
3. 93/68/EEC of 22 July 1993 amending the Directives 89/336/EEC, 91/263 /EEC and 92/31/EEC.(Marking Directive)
The Council Directive 92/31/EEC of 28 April 1992 amending directive on the approximation of the laws of the member states relating to electromagnetic compatibility.
If you have questions about your ZyXEL product or desire assistance, contact ZyXEL Communications Corporation in one of the following ways:
∙ Phone : In North America call between 8:00 AM and 5:00 PM PST at (714) 693-0808
Outside North America, you can dial +886-3-5783942 EXT 252 between 8:00AM and 5:00PM Taiwan time (GMT +8:00).
∙ Fax : ZyXEL in North America: (714) 693-8811 or Taiwan: +886-3-5782439
For European and Asian versions and related files, use the address: ftp.zyxel.co.at
∙ Postal Service : You can send written communications to the following address:
ZyXEL Communications Corporation
6, Innovation Road II, Science-Based Industrial Park Hsinchu, Taiwan 300, R.O.C.
ZyXEL Communications Inc. 4920 E. La Palma Avenue Anaheim, CA92807, U.S.A.
ZyXEL Limited Warranty ii
FCC Part 15 Information iii
Information for Canadian Users iv
Contacting ZyXEL vi
1 Introduction 1
What This Manual Covers 1
Modem Features 1
Standard Features 1
Intelligent Features 2
Fax Compatibility 3
Technical Specifications 3
Unpacking Your Modem 4
Enclosed Equipment 4
Required Equipment 4
Becoming a Registered Owner 5
2 Installation 7
U-336R/RE Modem Card 7
Required Steps for U-336R/RE Installation 9
Installing the modem card 10 Connect to phone lines 10 Connect to Computers 11 Hooking Up Power 11
Fax/Modem Communication Software Installation 11
3 Basic Modem Operation 15
Understanding AT Commands 15
Using the Windows 95 Hyper Terminal Program 15
Dialing and Answering Techniques 17
Dialing using the ATD Command 17 Auto-Answer and Hook Controls 18
Making Your First Connection 18
Quick Tips when issuing AT Commands 19
Modem Result Codes 21 Viewing S Register Values 22 Changing S Register Values 22
Non-Volatile Memory 23
Storing Phone Numbers 23 Dialing Stored Phone Numbers 23
Saving Settings and User Profiles 24
Helpful Hints for PC Computers 24
Default Modem Settings for PC’s 25 ZyXEL Serial/Parallel I/O Card 25
Helpful Hints for Macintosh Computers 26
Special AT Command Settings for Macintosh 26 Macintosh Serial Port 26
Mac Software Tips 26
Helpful Hints for UNIX-Based Computers 27
Serial Cable 27
Basic Modem Settings for UNIX 27 Unix Software Tips 28
4 Synchronous Mode Operation 29
V.25bis Command Set 29 Clock Options 30
Command State Options 32 Dialing from Synchronous Mode 32
Answering from Synchronous Mode 33
Auto-Answer 33 Manual Answer 33
5 Leased Line Operation 35
Connecting to a Leased Line 35
Line Type Setting 35 Power Level Setting 36
Leased Line Handshaking 36
Manual Connect 36
Auto Handshake 36
Leased-Line Dial Backup 37
Aborting from Leased-Line Operation 38
Terminating a Leased Line Connection 38
6 Special Functions 39
Security Functions 39
Levels of Security 39
User Passwords 40
Remote Configuration 42
Caller Number Delivery (Caller ID) 43
Distinctive Ring 46
Extended Distinctive Ring (EDR) 47
Setting Up EDR 49
EDR Application Example 50
7 Fax Operation 53
Modem as Fax Machine 53
ITU-T T.30 Fax Protocol 54
Fax Command sets 54
Defining the Fax Command Sets 54 Class 1 Command Set 55
Class 2 Command Set 56
Class 2.0 Command Set 63 Extended Fax AT Command Set 70 Flow Control 74
Fax Reception from a BBS 75
8 AT Command Set Summaries 77
Basic AT Command Set 77
Description of ATI2 Output: 80
Extended AT& Command Set 83
Extended AT* Command Set 89
9 Status Registers & Result Codes 92
S-Register Descriptions 92
Basic S-Registers "ATSn=x" 92 Extended S-Registers "ATSn=x" 93
Result Code Options 111
"ATXn" Result Code Option Table 111 Result Code Field Descriptions 113
Connect Strings for Error Corrected Connections 113
10 Diagnostics & Troubleshooting 116
Power-On Self Test 117
Loopback Tests 118
Indicator Lights 119
Line Condition Status Display 120
Link Status Report (ATI2) 122
Trouble Shooting 126
AT Command Set Problems 126
Command Echo Problems 128
Answer Problems 128
Dialing Problems 129
Data Transfer Problems 130
Connect Problems 130
11 Upgrading Your Modem 131
Upgrading by Flash EPROM 131
Kernel Recovery Mode 132
12 Terminal Pinouts 133
Terminal Blocks 133
PC Serial Port Pinouts 134
Macintosh Serial Port Pinouts 135
What This Manual Covers
Congratulations on the purchase of your U-336R/RE modem - one of ZyXEL's premier high-performance products. The U-336R/RE modem cards are world renown for their ability to maintain ultra high speeds and clear, quality connections while communicating around the globe.
No other 33.6 Kbps modem gives you so much for so little. Your modem is equipped with an array of standard and Intelligent features designed to make your data communications faster, easier, and more convenient.
∙ Supports V.34 for 28,800bps and is backwards compatible.
∙ Operates in all environments including: Windows 95, DOS, Windows, Macintosh, OS/2, UNIX, Novell, Amiga, and IBM AS400/RS6000.
∙ V.42 and MNP 4/3 error correction.
∙ V.42bis and MNP 5 data compression.
∙ DTE serial interface with speeds up to 460.8Kbps.
∙ 14 LED indicators (RE/RD).
∙ 15 LED indicators (R).
∙ Extended AT command set with V.25bis.
∙ Operates on 2-wire dial-up or 2-wire leased line (RE).
∙ Operates on 2-wire dial-up or 2/4-wire leased line (R).
∙ Automatic data, and fax call detection allows you to use a single telephone line to handle both voice and data calls.
∙ Asynchronous and synchronous modes for reliable serial data communication.
∙ Fast retrain with automatic fall-forward and fall-back. Your modem will automatically fall back to lower speeds when communicating with slower modems and when encountering unstable or variable line conditions.
∙ Call-back security and password protection restricts access to authorized callers only.
∙ Caller ID identifies incoming calls before you answer (you must subscribe to this service through your telephone company in order for your modem to identify callers).
∙ Distinctive ring detects data, fax and voice calls (this feature requires communication software that supports distinctive ring, such as ZFAX)
∙ Remote configuration capability.
∙ EDR (extended Distinctive Ring).
∙ Flash EPROM memory lets you easily upload new firmware, providing you with easy access to new features.
∙ ZyXEL exclusive Kernel Recovery Mode for no hassle recovery from failed flash uploads - no factory repairs.
∙ EIA Class 1, 2, and 2.0 Fax commands.
∙ ITU-T V.17 G3: up to 14,400bps.
∙ ITU-T V.29 G3: up to 9,600bps.
∙ ITU-T V.27ter G3: up to 4,800bps.
∙ ZyXEL Fax AT commands.
∙ Operating mode: auto-dial/answer.
∙ Flow control: software XON/XOFF or hardware CTS/RTS.
∙ Data/Voice toggle switch.
∙ Configuration settings: software programmable with nonvolatile memory for phone number/profile storage.
∙ Diagnostics: self test, analog loopback (with self test), digital loopback, and remote digital loopback (with self test).
∙ Dialing type: tone/pulse dialing.
∙ Line interface: 2-wire dial-up or 2-wire leased line (RE).
∙ Line interface: 2-wire dial-up or 2/4-wire leased line (R).
∙ Call progress monitoring: dial tone, busy, and ring back detection.
∙ Audio Monitor: programmable volume control.
Unpacking Your Modem
Before you proceed further, please check all items you received with your modem against this list to make sure nothing is missing. The complete package should include:
∙ One U-336R/RE universal modem.
∙ One warranty/registration card.
Contact your dealer or the store where you bought the modem if anything is missing. Check the modem for shipping damages. If you find any damage, contact the shipping agency immediately.
Retain shipping and cushioning materials for future storage or shipping needs.
Please direct any additional questions about damaged or missing materials to your dealer or distributor, or see page vi to contact ZyXEL.
In addition to the ZyXEL modem you just purchased, you must have the following equipment to operate your modem:
∙ Available PC serial port with a high-speed 16550 UART.
∙ Standard "straight-through” RS-232 cable (pins 1-8, 20, 22).
∙ Available telephone jack.
∙ Available AC wall outlet.
∙ Telephone line from your telephone company (dial-up or leased line).
∙ Data and fax communication software.
Becoming a Registered Owner
Complete the pre-addressed Warranty Registration Card and place it in the mail. Registered owners will receive future product information and update announcements. Warranty registration is not necessary for product repair or replacement. Also save your dated invoice as proof of purchase.
This chapter covers the steps required to install your U-336R/RE modem into a ZyXEL RS-1612 rack system. A separate comprehensive manual containing rack system information is included with your modem rack chassis.
U-336R/RE Modem Card
The U-336R front panel consists of fifteen LED indicators and two switches. The U-336RE front panel consists of fourteen LED indicators and two switches. The LEDs on the front panel, display the current status and configuration of the modem. Refer to the following table for details on the LED status indicators and their meaning.
Добрый день! Обрисую полностью ситуацию. Есть старые модемы марки Zyxel u 336s которые через двух проводку должны соединять 2 компьютера на расстояние в 17 км. Решили пока настроить модемы , и компьютер при настройку выполнял как указано руководстве но при воде команд в Hyperterminale когда ввожу AT не каких признаков соединения нет на модеме горят лампочки DSR , CTS , DTR , RTS в руководстве указана что если команды не водится проверить лампочку DTR если она не горит то компьютер к модему не подключен.Попробовал настроить другой модем но там получилось так что горят только два индикатора DSR , CTS хотя перенес те же настройки в модемах в меню стоят настройки с прошлого места где они были настройки я пытался поделать как в модемах. Пожалуйста кто разбирается в этом помогите , и обеснить как их можно настроить для чайника заранее буду благодарен.
Уточните, под "двух проводкой" в вашем случае понимается физическая (выделенная линия) или телефонная линия.
Если используется выделенная линия, то расстояние в 17 км, пожалуй, великовато для этого модема, на сколько я помню, 10-12км было еще реальным для передачи данных, более 14км связь вообще не устанавливалась.
Это примерное расстояние но скорее всего оно меньше а имеется виду физическая (выделенная линия) между объектами проведен двух проводный кабель которым и хотим воспользоваться.
Проверку работоспособности модема с компьютером мы проверяли путем опроса модема в диспетчере задач >свойства модема >диагностика >опросить модем. Затем два компьютера соединяли двумя модемами и пытались проверить их в совместной работе, при этом один модем устанавливался в "режим вызова", а другой - в "режим ответа". Наборы команд я уже не помню (давно это было). Попробуйте по инструкции.
Что при выборе опросить модем возникает ошибка то что модем не найден индикация на модеме свидетельствует о том что подключение есть возможно проблема в настройках но в каких?
Попробуйте из терминальной программы ввести следующую последовательность:
Для вызывающего модема:
>AT
>OK
>AT &F L7 &D0 &H0 &K4 &M2 &N0 *Q2 *M0 &W0
>OK
>AT S20=11 S35=2 S7=20 &W0
>OK
>AT &L1 &W0
>OK
>AT Q1 &W0 Z0
|
+- отключает ответ модема, поэтому “OK” не увидим
Для отвечающего модема:
>AT
>OK
>AT &F L7 &D0 &H0 &K4 &M2 &N0 *Q2 *M1 &W0
>OK
>AT S20=11 S35=2 S7=20 &W0
>OK
>AT &L1 &W0
>OK
>AT Q1 &W0 Z0
|
+- отключает ответ модема, поэтому “OK” не увидим
Описание параметров программирования модемов ZyXEL.
Qn - режим выдачи результирующих кодов выполнения команд и операций
Q0 - модем возвращает результирующие коды
Q1 - модем не возвращает результирующие коды
Ln - громкость встроенного динамика (0-7)
Zn - загрузка конфигурации из профиля 0 (варианты: 0-4), соответствует ATZ
Z4 – загрузить заводскую конфигурацию
&Dn - Сигнал готовности терминала DTR
&D0 - модем считает, что терминал всегда готов к работе DTR всегда ON
&D1 - включение сигнала DTR вызывает набор определенного номера телефона (*Dn)
&D2 - выключение сигнала DTR прерывает соединение
&D3 - выключение сигнала DTR прерывает соединение и загружает рабочую конфигурацию
&F - загрузить заводские установки в качестве рабочей конфигурации
&Hn - управление потоком данных DTE/DCE отключено
&H0 - управление отключено
&H3 - управление аппаратное RTS/CTS
&H4 - управление программное (XON/XOFF)
&Kn - коррекция ошибок не используется
&K0 - коррекция ошибок не используется
&K2 - MNP4+MNP3
&K3 - V.42+MNP4
&K4 - V.42 V.42bis+MNP4+MNP5
&L1 - Режим 2-х проводная выделенная линия
&L0 - обычная 2-х проводная коммутируемая линия
&L1 - 2-х проводная выделенная линия
&L2 - 4-х проводная выделенная линия
&M2 - прямой асинхронный режим без буферизации данных
&M0 - асинхронный режим с буферизацией данных
&M1 - асинхронный командный режим, синхронный при передаче данных
&M2 - прямой асинхронный режим без буферизации данных
&M3 - синхронный режим
&Nn - режим работы по линии:
&N0 - Multi-Auto (автоматический выбор, максимально-возможной скорости)
&N5 - V.32 4800
&N35 - ZyXEL 16800
&Zn=s- записать телефонный номер s в позицию n запоминающего устройства модема.
Для указания номера позиции набора по умолчанию используйте команду AT*Dn или ATS29=n
&Wn - сохранение текущей конфигурации в профиль n
*Bn - набор резервного номера из заданной позиции (см.&Zn) при обрыве выделенной линии.
Номер позиции на единицу больше используемого в команде &Zn
*M0 - установка модема как ведущего (варианты: 0 – ведущий, 1 – ведомый)
*Q3 - реакция на изменение качества связи
*Q0 - не реагировать на ухудшение качества
*Q1 - повтор процедуры установления связи при плохом качестве
*Q2 - адаптивное изменение скорости (уменьшение/увеличение)
*Q3 - прекращение связи при плохом качестве связи
S0=nn число звонков, после которого надо снять трубку в режиме ответа
S6=nn время ожидания перед набором номера
S7=nn время ожидания несущей в секундах
S20=nn скорость канала DTE (терминал) 4800
0 – 230400 8 – 12000
2 – 76800 9 – 9600
3 – 57600 10 – 7200
4 – 38400 11 – 4800
5 – 19200 12 – 2400
6 – 16800 13 – 1200
7 – 14400 14 – 460800
S34=nn время работы по резервной (коммутируемой линии связи). 0-возврата на выделенную линию не происходит.
S35=2 отключение прерывание с терминала во время установления связи
S38=1 повторно набирать номер по умолчанию, если соединение не было установлено
S41=16 модем игнорирует распознавание зуммера на линии,
ждет перед дозвоном время, указанное в S6
Добрый день! Обрисую полностью ситуацию. Есть старые модемы марки Zyxel u 336s которые через двух проводку должны соединять 2 компьютера на расстояние в 17 км. Решили пока настроить модемы , и компьютер при настройку выполнял как указано руководстве но при воде команд в Hyperterminale когда ввожу AT не каких признаков соединения нет на модеме горят лампочки DSR , CTS , DTR , RTS в руководстве указана что если команды не водится проверить лампочку DTR если она не горит то компьютер к модему не подключен.Попробовал настроить другой модем но там получилось так что горят только два индикатора DSR , CTS хотя перенес те же настройки в модемах в меню стоят настройки с прошлого места где они были настройки я пытался поделать как в модемах. Пожалуйста кто разбирается в этом помогите , и обеснить как их можно настроить для чайника заранее буду благодарен.
Уточните, под "двух проводкой" в вашем случае понимается физическая (выделенная линия) или телефонная линия.
Если используется выделенная линия, то расстояние в 17 км, пожалуй, великовато для этого модема, на сколько я помню, 10-12км было еще реальным для передачи данных, более 14км связь вообще не устанавливалась.
Это примерное расстояние но скорее всего оно меньше а имеется виду физическая (выделенная линия) между объектами проведен двух проводный кабель которым и хотим воспользоваться.
Проверку работоспособности модема с компьютером мы проверяли путем опроса модема в диспетчере задач >свойства модема >диагностика >опросить модем. Затем два компьютера соединяли двумя модемами и пытались проверить их в совместной работе, при этом один модем устанавливался в "режим вызова", а другой - в "режим ответа". Наборы команд я уже не помню (давно это было). Попробуйте по инструкции.
Что при выборе опросить модем возникает ошибка то что модем не найден индикация на модеме свидетельствует о том что подключение есть возможно проблема в настройках но в каких?
Попробуйте из терминальной программы ввести следующую последовательность:
Для вызывающего модема:
>AT
>OK
>AT &F L7 &D0 &H0 &K4 &M2 &N0 *Q2 *M0 &W0
>OK
>AT S20=11 S35=2 S7=20 &W0
>OK
>AT &L1 &W0
>OK
>AT Q1 &W0 Z0
|
+- отключает ответ модема, поэтому “OK” не увидим
Для отвечающего модема:
>AT
>OK
>AT &F L7 &D0 &H0 &K4 &M2 &N0 *Q2 *M1 &W0
>OK
>AT S20=11 S35=2 S7=20 &W0
>OK
>AT &L1 &W0
>OK
>AT Q1 &W0 Z0
|
+- отключает ответ модема, поэтому “OK” не увидим
Описание параметров программирования модемов ZyXEL.
Qn - режим выдачи результирующих кодов выполнения команд и операций
Q0 - модем возвращает результирующие коды
Q1 - модем не возвращает результирующие коды
Ln - громкость встроенного динамика (0-7)
Zn - загрузка конфигурации из профиля 0 (варианты: 0-4), соответствует ATZ
Z4 – загрузить заводскую конфигурацию
&Dn - Сигнал готовности терминала DTR
&D0 - модем считает, что терминал всегда готов к работе DTR всегда ON
&D1 - включение сигнала DTR вызывает набор определенного номера телефона (*Dn)
&D2 - выключение сигнала DTR прерывает соединение
&D3 - выключение сигнала DTR прерывает соединение и загружает рабочую конфигурацию
&F - загрузить заводские установки в качестве рабочей конфигурации
&Hn - управление потоком данных DTE/DCE отключено
&H0 - управление отключено
&H3 - управление аппаратное RTS/CTS
&H4 - управление программное (XON/XOFF)
&Kn - коррекция ошибок не используется
&K0 - коррекция ошибок не используется
&K2 - MNP4+MNP3
&K3 - V.42+MNP4
&K4 - V.42 V.42bis+MNP4+MNP5
&L1 - Режим 2-х проводная выделенная линия
&L0 - обычная 2-х проводная коммутируемая линия
&L1 - 2-х проводная выделенная линия
&L2 - 4-х проводная выделенная линия
&M2 - прямой асинхронный режим без буферизации данных
&M0 - асинхронный режим с буферизацией данных
&M1 - асинхронный командный режим, синхронный при передаче данных
&M2 - прямой асинхронный режим без буферизации данных
&M3 - синхронный режим
&Nn - режим работы по линии:
&N0 - Multi-Auto (автоматический выбор, максимально-возможной скорости)
&N5 - V.32 4800
&N35 - ZyXEL 16800
&Zn=s- записать телефонный номер s в позицию n запоминающего устройства модема.
Для указания номера позиции набора по умолчанию используйте команду AT*Dn или ATS29=n
&Wn - сохранение текущей конфигурации в профиль n
*Bn - набор резервного номера из заданной позиции (см.&Zn) при обрыве выделенной линии.
Номер позиции на единицу больше используемого в команде &Zn
*M0 - установка модема как ведущего (варианты: 0 – ведущий, 1 – ведомый)
*Q3 - реакция на изменение качества связи
*Q0 - не реагировать на ухудшение качества
*Q1 - повтор процедуры установления связи при плохом качестве
*Q2 - адаптивное изменение скорости (уменьшение/увеличение)
*Q3 - прекращение связи при плохом качестве связи
S0=nn число звонков, после которого надо снять трубку в режиме ответа
S6=nn время ожидания перед набором номера
S7=nn время ожидания несущей в секундах
S20=nn скорость канала DTE (терминал) 4800
0 – 230400 8 – 12000
2 – 76800 9 – 9600
3 – 57600 10 – 7200
4 – 38400 11 – 4800
5 – 19200 12 – 2400
6 – 16800 13 – 1200
7 – 14400 14 – 460800
S34=nn время работы по резервной (коммутируемой линии связи). 0-возврата на выделенную линию не происходит.
S35=2 отключение прерывание с терминала во время установления связи
S38=1 повторно набирать номер по умолчанию, если соединение не было установлено
S41=16 модем игнорирует распознавание зуммера на линии,
ждет перед дозвоном время, указанное в S6
Что при выборе опросить модем возникает ошибка то что модем не найден индикация на модеме свидетельствует о том что подключение есть возможно проблема в настройках но в каких?
Странно, что при опросе, модем не найден. В диспетчере устройств, в свойствах модема, какое состояние модема? Установлен ли драйвер тип и версия его. Правильно ли включены кабели, тип кабелей (разъемов)? Может с этого стоит начать поиск неисправностей. Под какой ОС произведена инсталляция модема?
Драйвера на XP и windows 7 кабеля в порядке разем R232 просто при воде команд не каких надписей нет состояние показывает что мадем есть.
Я правильно понял, что драйвера модема от Windows XP и установлен модем в Windows 7? или один модем установлен в Windows XP а другой в Windows 7? Посмотрите еще в настройках модема >дополнительные параметры связи >дополнительные параметры >номер COM порта, используемого модемом, а также что у вас есть разделе диспетчера "Порты (COM и LPT)"
Один модем установлен компютеру с виновс xp подключен к Com1 в настройках компютер видит модем но команды не проходят. Другой компютер с виндовс 7 установлины драйвера с с совместимостью для xp,7,8
настройки такиеже но индекация на модеме не показывает подключения а к икспишному показыват.
а). Номер COM порта, используемого модемом, вы взяли из "дополнительных параметров" модемов в диспетчерах устройств обеих ОС?
б).Что у вас есть разделах диспетчеров "Порты (COM и LPT)" обеих ОС?
До тех пор, пока не решена проблема опроса устройств в диспетчерах устройств, не имеет смысла использовать терминалы для программирования модемов, я думаю. Диагностика может затянуться на долго. Есть подозрение, что не верно используются COM порты или IRQ, поэтому надо как то аккуратненько это все проверить. Если вы не против, предлагаю сразу все разбить на два независимых анализа: модем1 и Windows XP, модем2 и Windows 7.
1. снимите кобель между модемами, перезагрузите обе системы;
2. перед загрузкой Windows XP, зайдите в BIOS и помотрите, какие COM порты заблокированы;
3. после загрузки Windows 7, попробуйте протестировать устройства диагностикой:
Центр поддержки\Устранение неполадок\Просмотр всех категории\Оборудование и устройства
4. после загрузки Windows XP, попробуйте изменить в диспетчере устройств используюемый COM1 порт на COM2, перезагрузитесь и попробуйте выполнить опрос модема еще раз.
Результаты сообщите также по пунктам, чтобы я не путался.
Через биос не пробовал в компютере с xp есть только COm 1 и LPT принтер COM 2 не где нету. Но у самих модемов есть настройки через жк дисплей и там выставлены настройки которые быле на прошлом месте их установки возможно в этом причина?
Возможно конечно. Можете вы переписать все настройки, ранее заданные в модемах и сохранить их на будущее? А как с диагностикой на windows 7? Если записать старые настройки удастся, то я бы попробовал изменить настройку в диспетчере Windows XP на COM2, и в диспетчере Windows 7 на COM2, после безуспешной диагностики. Что-то надо пробовать, не хочется вам советовать переинсталляцию модемов. Честно сказать, не помню, можно ли их сбросить к заводским установкам.
На 7 даже индикаторы не загарельсь указывающие на подключение как на xp хотя все водил тоже самое кабель менел и он рабочий.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or remanufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.
Note: Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind or character to the purchaser.
To obtain the services of this warranty, please contact ZyXEL’s Service Center, refer to the separate Warranty Card for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid (USA and territories only). If the customer
desires some other return destination beyond the U.S. borders, the customer shall bear the cost of the return shipment. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Copyright © 1999 by ZyXEL
The contents of this book may not be reproduced (in any part or as a whole) or transmitted in any form or by any means without the written permission of the publisher.
Published by ZyXEL Communications Corporation. All rights reserved.
Note: ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patents rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This document is subject to change without notice.
Trademarks mentioned in this manual are used for informational purposes only.
Trademarks are properties of their respective owners.
FCC Part 15 Information
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operations.
This equipment has been tested and found to comply with the limits for a CLASS A digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
∙ Reorient or relocate the receiving antenna.
∙ Increase the separation between the equipment and the receiver.
∙ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
∙ Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded RS-232 cables are required to be used to ensure compliance with FCC Part 15, and it is the responsibility of the user to provide and use shielded RS-232 cables.
Information for Canadian Users
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Industry Canada does not guarantee that the equipment will operate to a user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly. The customer should be aware that the compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
For their own protection, users should ensure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.
This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry Canada.
The declarations of CE marking:
Note: This applies only for U-336S model.
This product has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I.420 (Basic Rate ISDN user access). This product complies with the following directives:
1. The Council Directive 89/336/EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility. (EMC Directive)
2. Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecommunication terminal equipment. (The Telecom Terminal Equipment Directive)
3. 93/68/EEC of 22 July 1993 amending the Directives 89/336/EEC, 91/263 /EEC and 92/31/EEC.(Marking Directive)
The Council Directive 92/31/EEC of 28 April 1992 amending directive on the approximation of the laws of the member states relating to EletoMagnetic Compatibility.
If you have questions about your ZyXEL product or desire assistance, contact ZyXEL Communications Corporation in one of the following ways:
∙ Phone : In North America call between 8:00 AM and 5:00 PM PST at (714) 693-0808
Outside North America, you can dial +886-3-5783942 between 8:00AM and 5:00PM Taiwan time (GMT +8:00).
∙ Fax : ZyXEL in North America: (714) 693-8811 or Taiwan: +886- 3-5782439
For European versions and related files, use the address: ftp.zyxel.co.at
∙ Postal Service : You can send written communications at the following address:
ZyXEL Communications Corporation
6, Innovation Road II, Science-Based Industrial Park Hsinchu, Taiwan 300, R.O.C.
ZyXEL Communications Inc. 1650 Miraloma Avenue Placentia, CA92870, U.S.A.
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or remanufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions.
Note: Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind or character to the purchaser.
To obtain the services of this warranty, please contact ZyXEL’s Service Center, refer to the separate Warranty Card for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid (USA and territories only). If the customer
desires some other return destination beyond the U.S. borders, the customer shall bear the cost of the return shipment. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Copyright © 1999 by ZyXEL
The contents of this book may not be reproduced (in any part or as a whole) or transmitted in any form or by any means without the written permission of the publisher.
Published by ZyXEL Communications Corporation. All rights reserved.
Note: ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patents rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This document is subject to change without notice.
Trademarks mentioned in this manual are used for informational purposes only.
Trademarks are properties of their respective owners.
FCC Part 15 Information
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operations.
This equipment has been tested and found to comply with the limits for a CLASS A digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
∙ Reorient or relocate the receiving antenna.
∙ Increase the separation between the equipment and the receiver.
∙ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
∙ Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded RS-232 cables are required to be used to ensure compliance with FCC Part 15, and it is the responsibility of the user to provide and use shielded RS-232 cables.
Information for Canadian Users
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Industry Canada does not guarantee that the equipment will operate to a user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly. The customer should be aware that the compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
For their own protection, users should ensure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.
This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of Industry Canada.
The declarations of CE marking:
Note: This applies only for U-336S model.
This product has been approved for connection to the Public Switched Telecommunication Network using interfaces compatible with ITU-TSS recommendation I.420 (Basic Rate ISDN user access). This product complies with the following directives:
1. The Council Directive 89/336/EEC of 3 May 1992 on the approximation of the laws of the member states relation to Electro Magnetic Compatibility. (EMC Directive)
2. Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecommunication terminal equipment. (The Telecom Terminal Equipment Directive)
3. 93/68/EEC of 22 July 1993 amending the Directives 89/336/EEC, 91/263 /EEC and 92/31/EEC.(Marking Directive)
The Council Directive 92/31/EEC of 28 April 1992 amending directive on the approximation of the laws of the member states relating to EletoMagnetic Compatibility.
If you have questions about your ZyXEL product or desire assistance, contact ZyXEL Communications Corporation in one of the following ways:
∙ Phone : In North America call between 8:00 AM and 5:00 PM PST at (714) 693-0808
Outside North America, you can dial +886-3-5783942 between 8:00AM and 5:00PM Taiwan time (GMT +8:00).
∙ Fax : ZyXEL in North America: (714) 693-8811 or Taiwan: +886- 3-5782439
For European versions and related files, use the address: ftp.zyxel.co.at
∙ Postal Service : You can send written communications at the following address:
ZyXEL Communications Corporation
6, Innovation Road II, Science-Based Industrial Park Hsinchu, Taiwan 300, R.O.C.
ZyXEL Communications Inc. 1650 Miraloma Avenue Placentia, CA92870, U.S.A.
Читайте также: