Командой drafting settings в autocad можно настроить
Панель Polar Angle Settings позволяет установить числовое значение полярного угла, кратно которому будет выполняться отслеживание. Панель содержит раскрывающийся список, поле ввода, кнопку-переключатель и две кнопки.
- Раскрывающийся список Increment Angle позволяет выбрать числовое значение полярного угла из прилагаемого перечня. Список снабжен контекстным меню.
- Флажок Additional angles разрешает ввод дополнительных числовых значений полярных углов в расположенном ниже поле ввода.
- Кнопка New позволяет ввести дополнительные числовые значения полярных углов. После щелчка по кнопке становится доступным поле ввода и устанавливается флажок Additional angles.
- Кнопка Delete позволяет удалить числовое значение дополнительного полярного угла, выбранное в поле ввода дополнительных числовых значений полярных углов.
Панель Object Snap Tracking Settings позволяет управлять направлениями отслеживания. Панель содержит две кнопки выбора.
- Кнопка выбора Track orthogonally only устанавливает только ортогональные направления отслеживания.
- Кнопка выбора Track using all polar angle settings разрешает все направления отслеживания.
Панель Polar Angle measurement позволяет определить начало отсчета углов отслеживания. Панель содержит две кнопки выбора.
- Кнопка выбора Absolute устанавливает измерение углов в абсолютной системе координат.
- Кнопка выбора Relative to last segment устанавливает измерение углов относительно последнего созданного сегмента.
Вкладка Object Snap (рис. 2.22) диалогового окна Drafting Settings позволяет настроить параметры режима объектной привязки. Вкладка содержит две кнопки-переключателя и одну панель.
- Флажок Object Snap On включает режим постоянной объектной привязки.
- Флажок Object Snap Tracking On включает режим постоянной объектной привязки для режима полярной трассировки.
- Панель Object Snap Modes содержит перечень характерных точек объектов, которые можно включить в постоянный набор объектных привязок или исключить из набора с помощью установки флажков.
Настройка параметров режимов черчения может быть выполнена также в командной строке с помощью команд GRID, LTSCALE, ORTHO, SNAP.
Рис. 2.22. Настройка параметров постоянного режима объектной привязки
Для настройки вспомогательных графических средств используется диалоговое окно Drafting Settings (Параметры вычерчивания), которое выводится на экран по команде TOOLS / DRAFTING SETTINGS . Аналогичный результат можно получит после введения команды DSETTINGS в командную строку.
Диалоговое окно Drafting settings имеет следующие компоненты:
Вкладка Snap and Grid (Шаг и Сетка) – задание режима перемещения курсора мыши только между точками, расположенных с фиксированным шагом. При установке этого режима графический курсор будет перемещаться только между этими точками
в зоне Snap задаются основные режима шаговой привязки
Snap x spacing — задается шаг привязки вдоль координатных осей X
Snap Y spacing — задается шаг привязки вдоль координатных осей Y
Angle – изменение наклона сетки привязки и изменение ориентации вспомогательной сетки и лучей перекрестия курсора
X base – задается от личные от 0 координаты начальной точки сетки привязки по оси Х
Y base – задается от личные от 0 координаты начальной точки сетки привязки по оси Y
в зоне Grid задается шаг вспомогательной ортогональной сетки, которая выводится на экран в виде точек, и покрывает рабочее поле чертежа, ограниченное лимитами. В процессе работы с рисунком AutoCAD позволяет включать и отключать видимость сетки и изменяет ее размер. Сетка не является частью рисунка и не выводится на плоттер. Как правило, шаг вспомогательной сетки устанавливается в 4..5 раз больше, чем шаг сетки привязки графического курс
в зоне Snap type & style обеспечивается задание типа сетки: ортогональной ( rectangular ), изометрической ( isometric ), или полярной ( polar )
Вкладка Polar tracking (Отслеживание направления) – это расширенный режим ортогонального вычерчивания с заданием параметров режима отслеживания опорных полярных углов и отслеживанием направления объектной привязки. Режим отслеживания направления позволяет задавать азимутальную сетку привязки с любым шагом по углу. В этом режиме при черчении пользователь может привязаться к определенным углам (0 0 , 90 0 , 180 0 , 270 0 ). Как только при отрисовке отрезка курсор оказывается в непосредственной близости от одного из назначенных опорных углов, он притягивается к направляющему вектору этого угла и выводит на экран окно указателя, в котором отображаются текущие относительные координаты курсора
флажок Polar tracking On – включение механизма отслеживания полярных углов
зона Polar angle settings позволяет задать значения опорных полярных углов. AutoCAD 2000i разрешает задать не более 10 значений опорных полярных углов
раскрывающийся список Increment angle – задается приращение значения полярного угла (минимальное приращение 5 0 ), т. е. задается шаг регулярной азимутальной сетки. Можно ввести точное значение полярного угла в текстовое поле, если установлен флажок Additional angle
флажок Additional angle разрешает перейти в режим задания дополнительных полярных углов
кнопка New – установка значения опорного полярного угла
зона Object snap tracking settings – используется для настройки параметров взаимосвязи опорных полярных углов и опций объектной привязки
Track orthogonally only – опция позволяющая использовать при объектной привязке только главные ортогональные направления (кратные 90 о )
Track using all polar angle settings – опция позволяющая использовать при объектной привязке все заданные значения полярных углов (все значения углов азимутальной сетки)
зона Polar angle measurement – зона, в которой задается направление отсчета полярных углов
Absolute – полярные углы задаются как абсолютные, отсчитываемые от направления в 0 0
Relative to last segments – полярные углы задаются как относительные, отсчитываемые от последнего сформированного на чертеже сегмента
Вкладка Object snap (Объектная привязка) обеспечивает включение и отключение режимов шаговой привязки, и изменение параметров. Включение режима позволяет «привязать» точки, вводимые с помощью мыши, к воображаемой сетке.
Кнопка Object snap on – кнопка включения режима объектной привязки
Кнопка Object snap tracking on – кнопка включения режима отслеживания объектной привязки
Зона Object Snap modes:
Endpoint (Конточка) — — привязка к ближайшей конечной точке отрезка, дуги или какого- либо другого из объектов чертежа midpoint (середина) — привязка к середине отрезка, дуги или какого- либо другого из объектов чертежа
Center (центр) — привязка к центру какого- либо из объектов чертежа.
Node (узел) — привязка к примитиву «точка» или точке вставки блока.
Quadrant (квадрант) — привязка к ближайшему квадранту круга или дуги, т. е. к точкам пересечения дуги или окружности с радиусами, имеющими направление (0,90,180,270) градусов.
Intersection (пересечение) — привязка к пересечению двух примитивов
Extension (продолжение) – обеспечивается растяжение указанной линии, привязка производится к ближайшей точке на этом продолжении
Insertion (точка вставки) — привязка к точке вставки формы, текста, атрибута или блока
Perpendicular (нормаль) — привязка к точке примитива, принадлежащей нормали (проведенной через эту точку) к данному объекту. Если режим указывается для первой точки, то строится отрезок перпендикулярный к существующему отрезку.
Tangent (касательная) — привязка к точке окружности или дуги, в которой прямая, проведенная из последней указанной точки, касается дуги или круга. Если режим указывается для первой точки, то строится отрезок касательный к дуге или кругу.
Nearest (ближайшая) — привязка к ближайшей (по нормали) к курсору мыши точке на объекте. Эта опция имеет приоритет перед режимом ортогонального вычерчивания
Apparent intersection (кажущееся пересечение) – привязка к воображаемой точке пересечения продолжений двух графических элементов
Parallel (параллельно) – опция позволяет установить конечную точку прямолинейного сегмента, что бы он был направлен параллельно выбранному графическому элементу. Привязка используется только при выполнении вычерчивания отрезка по команде LINE
Кнопка Options – обеспечивает открытие одноименного диалогового окна с активизированной вкладкой Drafting
‹ Пользовательская настройка AutoCAD 2000i
Вверх
Отображение точки на чертежах ›
By:
Specifies drafting settings organized for drawing aids.
Summary
Displays the General tab in the Application Preferences dialog box. You cannot access the Application Preferences dialog box from the Drafting Settings dialog box if you are running DSETTINGS transparently.
The following categories are available.
List of Options
The following options are displayed.
Snap and Grid Tab (Drafting Settings Dialog Box)
Specifies Snap and Grid settings.
Snap On
Turns Snap mode on or off. You can also turn Snap mode on or off by clicking Snap on the status bar, by pressing F9, or by using the SNAPMODE system variable.
Snap Spacing
Controls an invisible, rectangular grid of snap locations that restricts cursor movement to specified X and Y intervals.
Specifies the snap spacing in the X direction. The value must be a positive real number. (SNAPUNIT system variable)
Specifies the snap spacing in the Y direction. The value must be a positive real number. (SNAPUNIT system variable)
Equal X and Y Spacing
Forces the X and Y spacing to the same values for snap spacing and for grid spacing. The snap spacing intervals can be different from the grid spacing intervals.
Polar Spacing
Controls the PolarSnap™ increment distance.
Sets the snap increment distance when PolarSnap is selected under Snap Type & Style. If this value is 0, the PolarSnap distance assumes the value for Snap X Spacing. The Polar Distance setting is used in conjunction with polar tracking and/or object snap tracking. If neither tracking feature is enabled, the Polar Distance setting has no effect. (POLARDIST system variable)
Snap Type
Sets the snap style and snap type.
Sets the snap type to Grid. When you specify points, the cursor snaps along vertical or horizontal grid points. (SNAPTYPE system variable)
Sets the snap style to standard Rectangular snap mode. When the snap type is set to Grid snap and Snap mode is on, the cursor snaps to a rectangular snap grid. (SNAPSTYL system variable)
Sets the snap style to Isometric snap mode. When the snap type is set to Grid snap and Snap mode is on, the cursor snaps to an isometric snap grid. (SNAPSTYL system variable)
Sets the snap type to Polar. When Snap mode is on and you specify points with polar tracking turned on, the cursor snaps along polar alignment angles set on the Polar Tracking tab relative to the starting polar tracking point. (SNAPTYPE system variable)
Grid On
Turns the grid on or off. You can also turn grid mode on or off by clicking Grid on the status bar, by pressing Fn-F7 , or by using the GRIDMODE system variable.
Grid Style
Sets the grid style in 2D contexts. You can also set grid style by using the GRIDSTYLE system variable.
Dot Grid in 2D Model Space
Sets the grid style to dotted grid for 2D model space. (GRIDSTYLE system variable)
Dot Grid in Paper Space
Sets the grid style to dotted grid for sheet and layout. (GRIDSTYLE system variable)
Grid Spacing
Controls the display of a grid that helps you visualize distances.
Note: The limits of the grid are controlled by the LIMITS command and the GRIDDISPLAY system variable.
Specifies the grid spacing in the X direction. If this value is 0, the grid assumes the value set for Snap X Spacing. (GRIDUNIT system variable)
Specifies the grid spacing in the Y direction. If this value is 0, the grid assumes the value set for Snap Y Spacing. (GRIDUNIT system variable)
Major Line Every
Specifies the frequency of major grid lines compared to minor grid lines. Grid lines rather than grid dots are displayed when SHADEMODE is set to Hidden. (GRIDMAJOR system variable)
Grid Behavior
Controls the appearance of the grid lines that are displayed when SHADEMODE is set to Hidden.
Limits the density of the grid when zoomed out. (GRIDDISPLAY system variable)
Allow Subdivision Below Grid Spacing:
Generates additional, more closely spaced grid lines when zoomed in. The frequency of these grid lines is determined by the frequency of the major grid lines. (GRIDDISPLAY and GRIDMAJOR system variables)
Display Grid Beyond Limits
Displays the grid beyond the area specified by the LIMITS command. (GRIDDISPLAY system variable)
Polar Tracking Tab (Drafting Settings Dialog Box)
Controls the AutoTrack settings.
Polar Tracking On
Turns polar tracking on and off. You can also turn polar tracking on or off by pressing F10 or by using the AUTOSNAP system variable.
Polar Angle Settings
Sets the alignment angles for polar tracking. (POLARANG system variable)
Sets the polar increment angle used to display polar tracking alignment paths. You can select a common angle of 90, 45, 30, 22.5, 18, 15, 10, or 5 degrees from the list. (POLARANG system variable)
Makes any additional angles in the list available for polar tracking. The Additional Angles check box is also controlled by the POLARMODE system variable, and the list of additional angles is also controlled by the POLARADDANG system variable.
If Additional Angles is selected, lists the additional angles that are available. To add new angles, click New. To remove existing angles, click Delete. (POLARADDANG system variable)
Displays the Add New Angle dialog box. Up to 10 additional polar tracking alignment angles can be added.
Note: Before adding fractional angles, you must set the AUPREC system variable to the appropriate decimal precision to avoid undesired rounding. For example, if the value of AUPREC is 0 (the default value), all fractional angles you enter are rounded to the nearest whole number.
Deletes selected additional angles.
Object Snap Tracking Settings
Sets options for object snap tracking.
Track Orthogonally Only
Displays only orthogonal (horizontal/vertical) object snap tracking paths for acquired object snap points when object snap tracking is on. (POLARMODE system variable)
Track Using All Polar Angle Settings
Applies polar tracking settings to object snap tracking. When you use object snap tracking, the cursor tracks along polar alignment angles from acquired object snap points. (POLARMODE system variable)
Note: Clicking Polar and Otrack on the status bar also turns polar tracking and object snap tracking on and off.
Polar Angle Measurement
Sets the basis by which polar tracking alignment angles are measured.
Bases polar tracking angles on the current user coordinate system (UCS).
Relative to Last Segment
Bases polar tracking angles on the last segment drawn.
Object Snap Tab (Drafting Settings Dialog Box)
Controls running object snap settings. With running object snap settings, also called Osnap, you can specify a snap point at an exact location on an object. When more than one option is selected, the selected snap modes are applied to return a point closest to the center of the aperture box. Press TAB to cycle through the options.
Object Snap On
Turns running object snaps on and off. The object snaps selected under Object Snap Modes are active while object snap is on. (OSMODE system variable)
Object Snap Tracking On
Turns object snap tracking on and off. With object snap tracking, the cursor can track along alignment paths based on other object snap points when specifying points in a command. To use object snap tracking, you must turn on one or more object snaps. (AUTOSNAP system variable)
Object Snap Modes
Lists object snaps that you can turn on as running object snaps.
Snaps to the closest endpoint of an arc, elliptical arc, line, polyline segment, spline, region, or ray.
Snaps to the midpoint of an arc, ellipse, elliptical arc, line, polyline segment, region, spline, or xline.
Snaps to the center of an arc, circle, ellipse, or elliptical arc.
Snaps to a point object, dimension definition point, or dimension text origin.
Snaps to the centroid of any closed polylines and splines.
Snaps to a quadrant point of an arc, circle, ellipse, or elliptical arc.
Snaps to the intersection of an arc, circle, ellipse, elliptical arc, line, polyline, ray, region, spline, or xline. Extended Intersection is not available as a running object snap.
Note: You might get varying results if you have both the Intersection and Apparent Intersection running object snaps turned on at the same time.
Intersection and Extended Intersection do not work with edges or corners of 3D solids created in AutoCAD.
Causes a temporary extension line or arc to be displayed when you pass the cursor over the endpoint of objects, so you can specify points on the extension.
Note: When working in perspective view, you cannot track along the extension line of an arc or elliptical arc.
Snaps to the insertion point of an attribute, a block, or text.
Snaps to a point perpendicular to an arc, circle, ellipse, elliptical arc, line, polyline, ray, region, 2D solid, spline, or xline.
Deferred Perpendicular snap mode is automatically turned on when the object you are drawing requires that you complete more than one perpendicular snap. You can use a line, arc, circle, polyline, ray, or xline as an object from which to draw a perpendicular line. You can use Deferred Perpendicular to draw perpendicular lines between such objects. When the aperture box passes over a Deferred Perpendicular snap point, an AutoSnap ™ tooltip and marker are displayed.
Snaps to the tangent of an arc, circle, ellipse, elliptical arc, or spline. Deferred Tangent snap mode is automatically turned on when the object you are drawing requires that you complete more than one tangent snap. You can use Deferred Tangent to draw a line or xline that is tangent to arcs, polyline arcs, or circles. When the aperture box passes over a Deferred Tangent snap point, a marker and an AutoSnap tooltip are displayed.
Note: When you use the From option in conjunction with the Tangent snap mode to draw objects other than lines from arcs or circles, the first point drawn is tangent to the arc or circle in relation to the last point selected in the drawing area.
Snaps to the nearest point on an arc, circle, ellipse, elliptical arc, line, point, polyline, ray, spline, or xline.
Snaps to the visual intersection of two objects that do not intersect in 3D space but may appear to intersect in the current view.
Extended Apparent Intersection snaps to the imaginary intersection of two objects that would appear to intersect if the objects were extended along their natural paths. Apparent and Extended Apparent Intersection do not work with edges or corners of 3D solids created in AutoCAD.
Note: You might get varying results if you have both the Intersection and Apparent Intersection running object snaps turned on at the same time.
Constrains a line segment, polyline segment, ray or xline to be parallel to another linear object. After you specify the first point of a linear object, specify the parallel object snap. Unlike other object snap modes, you move the cursor and hover over another linear object until the angle is acquired. Then, move the cursor back toward the object that you are creating. When the path of the object is parallel to the previous linear object, an alignment path is displayed, which you can use to create the parallel object.
Note: Turn off ORTHO mode before using the parallel object snap. Object snap tracking and polar snap are turned off automatically during a parallel object snap operation. You must specify the first point of a linear object before using the parallel object snap.
Turns on all object snap modes.
Turns off all object snap modes.
Dynamic Input Tab (Drafting Settings Dialog Box)
Controls pointer input, dimension input, dynamic prompting, and the appearance of drafting tooltips.
Enable Pointer Input
Turns on pointer input. When pointer input and dimensional input are both turned on, dimensional input supersedes pointer input when it is available. (DYNMODE system variable)
Pointer Input
Displays the location of the crosshairs as coordinate values in a tooltip near the cursor. When a command prompts you for a point, you can enter coordinate values in the tooltip instead of in the Command window.
Shows an example of pointer input.
Displays the Pointer Input Settings dialog box.
Enable Dimension Input where Possible
Turns on dimensional input. Dimensional input is not available for some commands that prompt for a second point. (DYNMODE system variable)
Dimension Input
Displays a dimension with tooltips for distance value and angle value when a command prompts you for a second point or a distance. The values in the dimension tooltips change as you move the cursor. You can enter values in the tooltip instead of on the command line.
Shows an example of dimensional input.
Displays the Dimension Input Settings dialog box.
Dynamic Prompts
Displays prompts in a tooltip near the cursor when necessary in order to complete the command. You can enter values in the tooltip instead of on the command line.
Shows an example of dynamic prompts.
Show Command Prompting and Command Input near Crosshairs
Displays prompts in Dynamic Input tooltips. (DYNPROMPT system variable)
Show Additional Tips with Command Prompting
Controls whether tips for using Shift and Ctrl for grip manipulation are displayed. (DYNINFOTIPS system variable)
Вкладка Drafting (рис. 1.12) позволяет управлять настройкой режимов автоматической объектной привязки AutoSnap (используется для предварительного просмотра и оценки точек привязки) и автоматического отслеживания AutoTrack (используется для расширения возможности определения точек относительно геометрии другого объекта).
Рис. 1.12. Настройка параметров режимов AutoSnap и AutoTrack
Вкладка содержит пять панелей.
Панель AutoSnap Settings позволяет управлять параметрами режима объектной привязки. Панель содержит четыре кнопки переключателя и раскрывающийся список AutoSnap Marker Color.
- Флажок Marker разрешает программе AutoCAD отображать геометрический символ (маркер), соответствующий характерной точке объекта при перемещении графического курсора поверх этого объекта. Режим используется по умолчанию. Установив текущее значение системной переменной AUTOSNAP – 1, можно также включить этот флажок из командной строки.
- Флажок Magnet разрешает автоматическое перемещение графического курсора на ближайшую зафиксированную характерную точку объекта (эффект примагничивания). Режим используется по умолчанию. Установив текущее значение системной переменной AUTOSNAP = 4, можно включить флажок из командной строки.
- Флажок Display AutoSnap Tooltip разрешает программе AutoCAD показывать вместе с геометрическим символом текстовое окно, в котором содержится название зафиксированной характерной точки объекта. По умолчанию флажок включен. Установив текущее значение системной переменной AUTOSNAP = 2, можно включить флажок из командной строки.
- Флажок Display AutoSnap Aperture Box разрешает появление "прицела" в месте пересечения перекрестий графического курсора при работе в режиме AutoSnap. По умолчанию флажок сброшен, поскольку изображения курсора и "прицела" забивают друг друга. Используя системную переменную АРВОХ, можно управлять появлением прицела из командной строки.
- Раскрывающийся список AutoSnap Marker Color позволяет выбрать цвет геометрических символов характерных точек объекта.
Панель AutoSnap Marker Size содержит шкалу, с помощью которой можно установить размеры геометрического символа (маркера) характерной точки объекта и информационное поле, отображающее текущие размеры маркера.
Панель AutoTrack Settings позволяет управлять параметрами режима трассировки. Панель содержит три флажка.
- Флажок Display Polar Tracking Vector включает или выключает отображение полярного вектора, который появляется при перемещении графического курсора вдоль направления трассировки. По умолчанию флажок установлен. Отключить отображение вектора можно также из командной строки, установив системную переменную TRACKPATH = 2.
- Флажок Display Full Screen Tracking Vector включает или выключает отображение полярного вектора на весь экран. По умолчанию флажок сброшен. Отключить отображение вектора можно также из командной строки, установив системную переменную TRACKPATH = 1.
- Флажок Display AutoTrack Tooltip разрешает программе AutoCAD показывать текстовое окно, в котором содержится информация по отслеживаемому направлению. По умолчанию флажок установлен. Установив текущее значение системной переменной AUTOSNAP = 32, можно включить это режим из командной строки.
Панель Alignment Point Acquisition позволяет выбрать способ захвата характерных точек объектов для последующей трассировки. Панель содержит две кнопки выбора.
- Кнопка выбора Automatic устанавливает при выполнении трассировки режим автоматического захвата характерных точек объекта.
- Кнопка выбора SHIFT to Acquire устанавливает для выполнения трассировки режим захвата характерных точек объекта только при нажатии клавиши SHIFT.
Панель Aperture Size содержит шкалу, с помощью которой можно установить размеры "прицела" для режима объектной привязки и информационное поле, отображающее текущие размеры "прицела". Размерами прицела управляет также системная переменная APERTURE.
List of Options
The following options are displayed.
Snap and Grid Tab (Drafting Settings Dialog Box)
Specifies Snap and Grid settings.
Snap On
Turns Snap mode on or off. You can also turn Snap mode on or off by clicking Snap on the status bar, by pressing F9, or by using the SNAPMODE system variable.
Snap Spacing
Controls an invisible, rectangular grid of snap locations that restricts cursor movement to specified X and Y intervals.
Specifies the snap spacing in the X direction. The value must be a positive real number. (SNAPUNIT system variable)
Specifies the snap spacing in the Y direction. The value must be a positive real number. (SNAPUNIT system variable)
Equal X and Y Spacing
Forces the X and Y spacing to the same values for snap spacing and for grid spacing. The snap spacing intervals can be different from the grid spacing intervals.
Polar Spacing
Controls the PolarSnap™ increment distance.
Sets the snap increment distance when PolarSnap is selected under Snap Type & Style. If this value is 0, the PolarSnap distance assumes the value for Snap X Spacing. The Polar Distance setting is used in conjunction with polar tracking and/or object snap tracking. If neither tracking feature is enabled, the Polar Distance setting has no effect. (POLARDIST system variable)
Snap Type
Sets the snap style and snap type.
Sets the snap type to Grid. When you specify points, the cursor snaps along vertical or horizontal grid points. (SNAPTYPE system variable)
Sets the snap style to standard Rectangular snap mode. When the snap type is set to Grid snap and Snap mode is on, the cursor snaps to a rectangular snap grid. (SNAPSTYL system variable)
Sets the snap style to Isometric snap mode. When the snap type is set to Grid snap and Snap mode is on, the cursor snaps to an isometric snap grid. (SNAPSTYL system variable)
Sets the snap type to Polar. When Snap mode is on and you specify points with polar tracking turned on, the cursor snaps along polar alignment angles set on the Polar Tracking tab relative to the starting polar tracking point. (SNAPTYPE system variable)
Grid On
Turns the grid on or off. You can also turn grid mode on or off by clicking Grid on the status bar, by pressing Fn-F7 , or by using the GRIDMODE system variable.
Grid Style
Sets the grid style in 2D contexts. You can also set grid style by using the GRIDSTYLE system variable.
Dot Grid in 2D Model Space
Sets the grid style to dotted grid for 2D model space. (GRIDSTYLE system variable)
Dot Grid in Paper Space
Sets the grid style to dotted grid for sheet and layout. (GRIDSTYLE system variable)
Grid Spacing
Controls the display of a grid that helps you visualize distances.
Note: The limits of the grid are controlled by the LIMITS command and the GRIDDISPLAY system variable.
Specifies the grid spacing in the X direction. If this value is 0, the grid assumes the value set for Snap X Spacing. (GRIDUNIT system variable)
Specifies the grid spacing in the Y direction. If this value is 0, the grid assumes the value set for Snap Y Spacing. (GRIDUNIT system variable)
Major Line Every
Specifies the frequency of major grid lines compared to minor grid lines. Grid lines rather than grid dots are displayed when GRIDSTYLE is set to 0. (GRIDMAJOR system variable)
Grid Behavior
Controls the appearance of the grid lines that are displayed when GRIDSTYLE is set to 0.
Limits the density of the grid when zoomed out. (GRIDDISPLAY system variable)
Allow Subdivision Below Grid Spacing:
Generates additional, more closely spaced grid lines when zoomed in. The frequency of these grid lines is determined by the frequency of the major grid lines. (GRIDDISPLAY and GRIDMAJOR system variables)
Display Grid Beyond Limits
Displays the grid beyond the area specified by the LIMITS command. (GRIDDISPLAY system variable)
Follow Dynamic UCS
Changes the grid plane to follow the XY plane of the dynamic UCS. (GRIDDISPLAY system variable)
Polar Tracking Tab (Drafting Settings Dialog Box)
Controls the AutoTrack settings.
Polar Tracking On
Turns polar tracking on and off. You can also turn polar tracking on or off by pressing F10 or by using the AUTOSNAP system variable.
Polar Angle Settings
Sets the alignment angles for polar tracking. (POLARANG system variable)
Sets the polar increment angle used to display polar tracking alignment paths. You can enter any angle, or select a common angle of 90, 45, 30, 22.5, 18, 15, 10, or 5 degrees from the list. (POLARANG system variable)
Makes any additional angles in the list available for polar tracking. The Additional Angles check box is also controlled by the POLARMODE system variable, and the list of additional angles is also controlled by the POLARADDANG system variable.
If Additional Angles is selected, lists the additional angles that are available. To add new angles, click New. To remove existing angles, click Delete. (POLARADDANG system variable)
Displays the Add New Angle dialog box. Up to 10 additional polar tracking alignment angles can be added.
Note: Before adding fractional angles, you must set the AUPREC system variable to the appropriate decimal precision to avoid undesired rounding. For example, if the value of AUPREC is 0 (the default value), all fractional angles you enter are rounded to the nearest whole number.
Deletes selected additional angles.
Object Snap Tracking Settings
Sets options for object snap tracking.
Track Orthogonally Only
Displays only orthogonal (horizontal/vertical) object snap tracking paths for acquired object snap points when object snap tracking is on. (POLARMODE system variable)
Track Using All Polar Angle Settings
Applies polar tracking settings to object snap tracking. When you use object snap tracking, the cursor tracks along polar alignment angles from acquired object snap points. (POLARMODE system variable)
Note: Clicking Polar and Otrack on the status bar also turns polar tracking and object snap tracking on and off.
Polar Angle Measurement
Sets the basis by which polar tracking alignment angles are measured.
Bases polar tracking angles on the current user coordinate system (UCS).
Relative to Last Segment
Bases polar tracking angles on the last segment drawn.
Object Snap Tab (Drafting Settings Dialog Box)
Controls running object snap settings. With running object snap settings, also called Osnap, you can specify a snap point at an exact location on an object. When more than one option is selected, the selected snap modes are applied to return a point closest to the center of the aperture box. Press TAB to cycle through the options.
Object Snap On
Turns running object snaps on and off. The object snaps selected under Object Snap Modes are active while object snap is on. (OSMODE system variable)
Object Snap Tracking On
Turns object snap tracking on and off. With object snap tracking, the cursor can track along alignment paths based on other object snap points when specifying points in a command. To use object snap tracking, you must turn on one or more object snaps. (AUTOSNAP system variable)
Object Snap Modes
Lists object snaps that you can turn on as running object snaps.
Snaps to the closest endpoint of an arc, elliptical arc, line, multiline, polyline segment, spline, region, or ray, or to the closest corner of a trace, solid, or 3D face.
Snaps to the midpoint of an arc, ellipse, elliptical arc, line, multiline, polyline segment, region, solid, spline, or xline.
Snaps to the center of an arc, circle, ellipse, or elliptical arc.
Snaps to a point object, dimension definition point, or dimension text origin.
Snaps to the centroid of any closed polylines and splines.
Snaps to a quadrant point of an arc, circle, ellipse, or elliptical arc.
Snaps to the intersection of an arc, circle, ellipse, elliptical arc, line, multiline, polyline, ray, region, spline, or xline. Extended Intersection is not available as a running object snap.
Intersection and Extended Intersection do not work with edges or corners of 3D solids.
Note: You might get varying results if you have both the Intersection and Apparent Intersection running object snaps turned on at the same time.
Causes a temporary extension line or arc to be displayed when you pass the cursor over the endpoint of objects, so you can specify points on the extension.
Note: When working in perspective view, you cannot track along the extension line of an arc or elliptical arc.
Snaps to the insertion point of an attribute, a block, a shape, or text.
Snaps to a point perpendicular to an arc, circle, ellipse, elliptical arc, line, multiline, polyline, ray, region, solid, spline, or xline.
Deferred Perpendicular snap mode is automatically turned on when the object you are drawing requires that you complete more than one perpendicular snap. You can use a line, arc, circle, polyline, ray, xline, multiline, or 3D solid edge as an object from which to draw a perpendicular line. You can use Deferred Perpendicular to draw perpendicular lines between such objects. When the aperture box passes over a Deferred Perpendicular snap point, an AutoSnap tooltip and marker are displayed.
Snaps to the tangent of an arc, circle, ellipse, elliptical arc, or spline. Deferred Tangent snap mode is automatically turned on when the object you are drawing requires that you complete more than one tangent snap. You can use Deferred Tangent to draw a line or xline that is tangent to arcs, polyline arcs, or circles. When the aperture box passes over a Deferred Tangent snap point, a marker and an AutoSnap tooltip are displayed.
Note: When you use the From option in conjunction with the Tangent snap mode to draw objects other than lines from arcs or circles, the first point drawn is tangent to the arc or circle in relation to the last point selected in the drawing area.
Snaps to the nearest point on an arc, circle, ellipse, elliptical arc, line, multiline, point, polyline, ray, spline, or xline.
Snaps to the visual intersection of two objects that are not in the same plane but may appear to intersect in the current view.
Extended Apparent Intersection is not available as a running object snap. Apparent and Extended Apparent Intersection do not work with edges or corners of 3D solids.
Note: You might get varying results if you have both the Intersection and Apparent Intersection running object snaps turned on at the same time.
Constrains a line segment, polyline segment, ray or xline to be parallel to another linear object. After you specify the first point of a linear object, specify the parallel object snap. Unlike other object snap modes, you move the cursor and hover over another linear object until the angle is acquired. Then, move the cursor back toward the object that you are creating. When the path of the object is parallel to the previous linear object, an alignment path is displayed, which you can use to create the parallel object.
Note: Turn off ORTHO mode before using the parallel object snap. Object snap tracking and polar snap are turned off automatically during a parallel object snap operation. You must specify the first point of a linear object before using the parallel object snap.
Turns on all object snap modes.
Turns off all object snap modes.
3D Object Snap Tab (Drafting Settings Dialog Box)
Controls running object snap settings for 3D objects. With running object snap settings, also called Osnap, you can specify a snap point at an exact location on an object. When more than one option is selected, the selected snap modes are applied to return a point closest to the center of the aperture box. Press TAB to cycle through the options.
3D Object Snap On
Turns 3D object snaps on and off. The 3D object snaps selected under 3D Object Snap Modes are active while object snap is on. (3DOSMODE system variable)
3D Object Snap Modes
Lists the 3D object snaps modes.
Snaps to the closest vertex of a 3D object.
Snaps to the midpoint of a face edge.
Snaps to the center of a face.
Snaps to a knot on a spline.
Snaps to a point perpendicular to a face.
Snaps to a point that is nearest to a 3D object face.
Turns on all 3D object snap modes.
Turns off all 3D object snap modes.
Dynamic Input Tab (Drafting Settings Dialog Box)
Controls pointer input, dimension input, dynamic prompting, and the appearance of drafting tooltips.
Enable Pointer Input
Turns on pointer input. When pointer input and dimensional input are both turned on, dimensional input supersedes pointer input when it is available. (DYNMODE system variable)
Pointer Input
Displays the location of the crosshairs as coordinate values in a tooltip near the cursor. When a command prompts you for a point, you can enter coordinate values in the tooltip instead of in the Command window.
Shows an example of pointer input.
Enable Dimension Input where Possible
Turns on dimensional input. Dimensional input is not available for some commands that prompt for a second point. (DYNMODE system variable)
Dimension Input
Displays a dimension with tooltips for distance value and angle value when a command prompts you for a second point or a distance. The values in the dimension tooltips change as you move the cursor. You can enter values in the tooltip instead of on the command line.
Shows an example of dimensional input.
Dynamic Prompts
Displays prompts in a tooltip near the cursor when necessary in order to complete the command. You can enter values in the tooltip instead of on the command line.
Shows an example of dynamic prompts.
Show Command Prompting and Command Input near Crosshairs
Displays prompts in Dynamic Input tooltips. (DYNPROMPT system variable)
Show Additional Tips with Command Prompting
Controls whether tips for using Shift and Ctrl for grip manipulation are displayed. (DYNINFOTIPS system variable)
By:
Specifies drafting settings organized for drawing aids.
Menu: Tools > Drafting Settings .
Summary
The following categories are available.
- Snap and Grid
- Polar Tracking
- Object Snap
- Dynamic Input
Читайте также: