J runner не видит xbox
ОБЯЗАТЕЛЬНО укажите модель и версию прошивки.
Если вы новичок на форуме, то задавая вопросы в темах, не забывайте проверять ответы.
Помните, что форум - это не чат, поэтому ответ можно получить не сразу, а спустя какое-то неопределённое время.
Имеется Бокс 360 Слим.
Прошивка LT+3.0
Дашбоард 13599
Новые игры под ЛТ+3.0 как Soul Calibur V работают нормально, записывал imgburn
А вот старые игры ( Tales of Vesperia, Soul Calibur 4) не работают, пишется - нераспознанный диск.
Помогите, в чем может быть дело?
Спасибо, что-то начало проясняться. Я понимаю что тут наверняка этим вопросом вас достали но не могли бы указать на мануал по патчингу?
Патчить нужно выходит вообще все игры где не написано под LT3.0 да? А то я думал надо патчить токо те где новая защита.
Kuroki Kaze добавил 12.02.2012 в 15:31
Перечитал кучу всего, пишут патчить надо токо игры с XGD3 защитой.
И писать на прошитом лаит он. Но это у меня работает как раз а вот игры 2-3 волны ума не приложу что делать как и чем патчить и как запустить, диск нечитаемый и все
Приветик, такая ситуация- сегодня взял с рук коробку, не запускается бэтмэн акхэм сити, дантэ инферно, асасинс чего то там, запускаются всякие соники, калибуры4, фэйбл2, помогите образумить моего малыша, если можно, то побольше ссылок, и как сделать, чтоб в лайве не банили, только своими руками, без обращения ко всяким васям, надеюсь на вас, ребята)))
Приветик, такая ситуация- сегодня взял с рук коробку, не запускается бэтмэн акхэм сити, дантэ инферно, асасинс чего то там, запускаются всякие соники, калибуры4, фэйбл2, помогите образумить моего малыша, если можно, то побольше ссылок, и как сделать, чтоб в лайве не банили, только своими руками, без обращения ко всяким васям, надеюсь на вас, ребята)))
ну я не знаю, какая техническая инфа может быть полезна и где ее взять, визуально выглядит так: появляется лого на xbox на белом фоне, консоль гудит, но ни через пять, ни через десять минут(Данте). А бэтмэн каже, что необходимо обновление, которого найти не удалось(диски тоже вчера купил). Вчера в гугле искал, и увидел такую инфу, мол начиная с какой то версии обновления дашборда вас принудительно возвращают на светлую сторону силы(шьется привод), и вытекает следующий вопрос: как безопасно обновить системное ПО, чтоб играть дальше в пиратки и как его обновить без плясок с барабаном, ну там с диска или флэшки. Просто мне тут в комплекте дали десяток дисков, не хотелось бы их выкидывать. Сам ящик уже старенький, но скока лет ему сказать не могу, без жесткого диска, по моему аркад
Нужно узнать прошивку привода и дашбоард. Могу посоветовать опытным путём. Скачиваешь игру под LT2 и LT3 и записываешь, так, которая 3апустится - и будет твоя прошивка. А дальше уже можно будет плясать.
Нужно узнать прошивку привода и дашбоард. Могу посоветовать опытным путём. Скачиваешь игру под LT2 и LT3 и записываешь, так, которая 3апустится - и будет твоя прошивка. А дальше уже можно будет плясать.
братка, ну не знаю я, скачивать мне несколько дней, моя ёта маст дай, может есть какой то тестер, типа на болванку кинул и все показало, как виктория и другие тесты на комп, приставка старенькая, бывший юзер рекомендовал обнов, но как и что ни он, ни я не в курсе
братка, ну не знаю я, скачивать мне несколько дней, моя ёта маст дай, может есть какой то тестер, типа на болванку кинул и все показало, как виктория и другие тесты на комп, приставка старенькая, бывший юзер рекомендовал обнов, но как и что ни он, ни я не в курсе
У мине все пиратки, кроме соника, он чересчур богато украшен, есть книжечка и голограмма, есть подозрение, что из светлых игр только он
Supfeer добавил 21.02.2012 в 17:22
А хрен его знает, если сам научусь, то и тебе помогу,ессно безвоздмездно, тока, удя по всему надо подождать, оставь конт, я тебе отпишу
tony12, насколько я начитался брать нужно приставку сделанную до августа 2011 года.
По поводу патча спасибо, уже разобрался, меня смущал просто момент в мануале что с лт2.0 на лт3.0 патчили, мне то надо было с более ранних прошивок игры патчить на лт3.0, вот и не мог мануал наити.
Но все равно решил фрибут делать, игры любого региона чтоб заработали.
Ребят такой вопрос : какие эмуляторы идут на прошивку Freeboot? (просто читал что идут разные от старых приставок а какие не указано..) может кто уже пробовал?
ошибка e64 что это еще такое :dash:на днях меняли плату и прошивали все шло ок а тут тебе на :o
Svetik79 добавил 21.05.2012 в 07:17
E64: DVD Drive Error - Dvd drive timed out during reset :Wrong firmware, dvd is without f/w chip, etc. This can also be caused by the tray not being fully closed on boot. also it could mean that the Kernel can't be launched/signature in NAND Flash chip is broken It could be possible after bad update. This might also be caused by a bad SATA cable.
Самый простой выход это еcли у тебя остался ключик от ориг прошивки твоего привода залить ключик в другой заведомо рабочий привод.
//у меня бокса нет, это все гугл. Но тот человек, что прошивал, должен понять написанное выше.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc. Перевод: zCarot
PSPx Forum - Сообщество фанатов игровых консолей.
J-Runner with Extras (17559) - Built in Timings, Bugfixes, and New Features! 3.0.3b & Delta Update
JRunner_V0.5 -добавлены Ричины прошивки, картинки с инструкциями для разных чипов и материнок (всё позаимстовано из сборки TWM)
Новая версия j_Runner также по 17559 даш
Добавлено:
Тайминги для прошивки чипов RGH1.2, S-RGH, RGH2 Zephyr.
Новые версии XeLL для мод прошивок RGH
Добавлена возможность прошивать чипы с помощью Matrix Flasher, а также прошивка самого флешера
Здравствуйте! А нет последней версии программы со вкладкой Images? В новой её нет, хотя картинок с инструкциями много добавилось.
Здравствуйте! А нет последней версии программы со вкладкой Images? В новой её нет, хотя картинок с инструкциями много добавилось.
Я в курсе. По этому и написал что много добавилось, но в старой версии, прямо из программы можно было картинку вызвать. Просто и удобно.
Всех с Новым годом!
Мы очень усердно работали, чтобы предоставить вам J-RUNNER С ДОПОЛНИТЕЛЬНЫМИ ФУНКЦИЯМИ V3.1.0, самое большое обновление за всю историю. Мы очень усердно работали, чтобы предоставить вам J-RUNNER С ДОПОЛНИТЕЛЬНЫМИ ФУНКЦИЯМИ V3.1.0, самое большое обновление за всю историю.
ОБЯЗАТЕЛЬНО укажите модель и версию прошивки.
Если вы новичок на форуме, то задавая вопросы в темах, не забывайте проверять ответы.
Помните, что форум - это не чат, поэтому ответ можно получить не сразу, а спустя какое-то неопределённое время.
Имеется Бокс 360 Слим.
Прошивка LT+3.0
Дашбоард 13599
Новые игры под ЛТ+3.0 как Soul Calibur V работают нормально, записывал imgburn
А вот старые игры ( Tales of Vesperia, Soul Calibur 4) не работают, пишется - нераспознанный диск.
Помогите, в чем может быть дело?
Спасибо, что-то начало проясняться. Я понимаю что тут наверняка этим вопросом вас достали но не могли бы указать на мануал по патчингу?
Патчить нужно выходит вообще все игры где не написано под LT3.0 да? А то я думал надо патчить токо те где новая защита.
Kuroki Kaze добавил 12.02.2012 в 15:31
Перечитал кучу всего, пишут патчить надо токо игры с XGD3 защитой.
И писать на прошитом лаит он. Но это у меня работает как раз а вот игры 2-3 волны ума не приложу что делать как и чем патчить и как запустить, диск нечитаемый и все
Приветик, такая ситуация- сегодня взял с рук коробку, не запускается бэтмэн акхэм сити, дантэ инферно, асасинс чего то там, запускаются всякие соники, калибуры4, фэйбл2, помогите образумить моего малыша, если можно, то побольше ссылок, и как сделать, чтоб в лайве не банили, только своими руками, без обращения ко всяким васям, надеюсь на вас, ребята)))
Приветик, такая ситуация- сегодня взял с рук коробку, не запускается бэтмэн акхэм сити, дантэ инферно, асасинс чего то там, запускаются всякие соники, калибуры4, фэйбл2, помогите образумить моего малыша, если можно, то побольше ссылок, и как сделать, чтоб в лайве не банили, только своими руками, без обращения ко всяким васям, надеюсь на вас, ребята)))
ну я не знаю, какая техническая инфа может быть полезна и где ее взять, визуально выглядит так: появляется лого на xbox на белом фоне, консоль гудит, но ни через пять, ни через десять минут(Данте). А бэтмэн каже, что необходимо обновление, которого найти не удалось(диски тоже вчера купил). Вчера в гугле искал, и увидел такую инфу, мол начиная с какой то версии обновления дашборда вас принудительно возвращают на светлую сторону силы(шьется привод), и вытекает следующий вопрос: как безопасно обновить системное ПО, чтоб играть дальше в пиратки и как его обновить без плясок с барабаном, ну там с диска или флэшки. Просто мне тут в комплекте дали десяток дисков, не хотелось бы их выкидывать. Сам ящик уже старенький, но скока лет ему сказать не могу, без жесткого диска, по моему аркад
Нужно узнать прошивку привода и дашбоард. Могу посоветовать опытным путём. Скачиваешь игру под LT2 и LT3 и записываешь, так, которая 3апустится - и будет твоя прошивка. А дальше уже можно будет плясать.
Нужно узнать прошивку привода и дашбоард. Могу посоветовать опытным путём. Скачиваешь игру под LT2 и LT3 и записываешь, так, которая 3апустится - и будет твоя прошивка. А дальше уже можно будет плясать.
братка, ну не знаю я, скачивать мне несколько дней, моя ёта маст дай, может есть какой то тестер, типа на болванку кинул и все показало, как виктория и другие тесты на комп, приставка старенькая, бывший юзер рекомендовал обнов, но как и что ни он, ни я не в курсе
братка, ну не знаю я, скачивать мне несколько дней, моя ёта маст дай, может есть какой то тестер, типа на болванку кинул и все показало, как виктория и другие тесты на комп, приставка старенькая, бывший юзер рекомендовал обнов, но как и что ни он, ни я не в курсе
У мине все пиратки, кроме соника, он чересчур богато украшен, есть книжечка и голограмма, есть подозрение, что из светлых игр только он
Supfeer добавил 21.02.2012 в 17:22
А хрен его знает, если сам научусь, то и тебе помогу,ессно безвоздмездно, тока, удя по всему надо подождать, оставь конт, я тебе отпишу
tony12, насколько я начитался брать нужно приставку сделанную до августа 2011 года.
По поводу патча спасибо, уже разобрался, меня смущал просто момент в мануале что с лт2.0 на лт3.0 патчили, мне то надо было с более ранних прошивок игры патчить на лт3.0, вот и не мог мануал наити.
Но все равно решил фрибут делать, игры любого региона чтоб заработали.
Ребят такой вопрос : какие эмуляторы идут на прошивку Freeboot? (просто читал что идут разные от старых приставок а какие не указано..) может кто уже пробовал?
ошибка e64 что это еще такое :dash:на днях меняли плату и прошивали все шло ок а тут тебе на :o
Svetik79 добавил 21.05.2012 в 07:17
E64: DVD Drive Error - Dvd drive timed out during reset :Wrong firmware, dvd is without f/w chip, etc. This can also be caused by the tray not being fully closed on boot. also it could mean that the Kernel can't be launched/signature in NAND Flash chip is broken It could be possible after bad update. This might also be caused by a bad SATA cable.
Самый простой выход это еcли у тебя остался ключик от ориг прошивки твоего привода залить ключик в другой заведомо рабочий привод.
//у меня бокса нет, это все гугл. Но тот человек, что прошивал, должен понять написанное выше.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc. Перевод: zCarot
PSPx Forum - Сообщество фанатов игровых консолей.
I am trying to run J-Runner v3.0.0b with a J-R Programmer v2 on a Jasper 512mb Xbox 360 console.
When I go to click on "Read Nand" I get :
Version: 10
Flash Config: 0x00000000
Console Not Found
I double checked my soldering points even though they would not win a beauty pageant they are sound nonetheless.
I have tested for continuity from the J-R Programmer board connector pins to the under the motherboard at the soldering points to make sure there's no break. I have rebooted my PC (done on a dual pc win7 64bit / win10 64bit and a win10 laptop) disconnected the motherboard from power then reconnect (not turning the xbox on) but I still get the same error message. I tried to play around with the switches on the device but that didn't change anything.
I am completely clueless as to what is going on. That programmer is brand new too. I am able to program a CoolRunner Rev C with it but for the life of me I can't detect the xbox.
mozbius
Newbie
I resoldered everything and retested again continuity. looked for possible board cuts. or short cause by my soldering. Still getting "no console found".
nothing special on the back.
Perhaps the programmer is faulty?
BluesMan67
Enthusiast
In your third photo,it looks like your red and orange wires are touching each other.
De-solder ALL your wires again,clean up the nand points on your Jasper board so they are clean of any flux or carbon.
Trim the ends off all your nand wires and re-do them (tip-twist the small end of each wire between your thumb and first finger) then add flux to each end and re-tin the ends with fresh solder.
Add fresh flux to the nand points on the Jasper board and add a little bit more solder to each point (some times the middle of those holes don't have the factory applied solder going all the way through) so it's always a good idea to pre-tin those holes till you see solder coming through the bottom of the hole underneath the board.
With the "Yellow" wire,you can solder that to the metal shield of the HDD socket/port instead of the point on the board (as the factory applied solder in that hole takes a bit of heat to melt it)
Then make sure your nand read/write wires are pushed all the way into the JR-Programmer socket.Then plug in your 360's power cable so you have standby power but DO NOT power on your console,just leave it with standby power.
Re-launch J-Runner and press "F2" on your keyboard.Fingers crossed you should now get the correct "Flash Config" details in J-Runner.
mozbius
Newbie
Thank you for your feedback it is greatly appreciated.
I want to note that the 3rd picture is misleading as the 5th picture shows that they are really not in contact.
Also my solder work may not have been good looking but it was definitely sound (I did pre-tined every wire). Like I said I did test for continuity from under the circuit board at one end and the pins behind the connector on the programmer at the other end for each soldered nand points. That basically means that the connector is reliably making contact with the wires and the soldering points are sound.
That being said I feel am not losing anything trying again for a 3rd time as suggested. So this time I went all out for the perfect looking soldering that I have ever done on a circuit board. I did again test for conductivity from under the motherboard all the way up to the pins behind the programmer's connector. I have also tested for potential short between all nand points. I have also alternatively soldered the yellow wire on the HDD's connector metal case. Then tried JRunner with the board (plugged to its power supply, NOT turned on) and I am still not getting the console to be seen.
NOTE: Not sure how significant that is but when I plug in the power (with the programmer NOT connected through USB) LD1 and LD2 quickly bleep (not full steady blinking just a barely noticeable bleep) before turning off completely. I posted a video of what it looks like.
What is RGH 3.0?
RGH 3.0 is the newest reset glitch hack method for Xbox 360 using just 2 wires and a new layout.
The resulting install is close to J-TAG simplicity and stability, NO Glitch Chips required!
The new method ensures that most if not ALL compatible Xbox 360s can be RGHed with results mostly returning INSTABOOT!
Compatibility
So far, RGH3.0 has been tested and confirmed to Instaboot on the following consoles:
Xbox 360 Phat:
Falcon
Jasper: Small Block (16mb) and Big Block (256/512mb)
Xbox 360 Slim + Slim "E":
Trinity
Corona V1 - V6
Winchester IS NOT SUPPORTED
YOU CANNOT RGH A WINCHESTER. PERIOD.
Need to Identify what Xbox 360 you have?
Click the button below:
Use the below image to help you identify your Xbox 360 Motherboard Type.
Manufacture Date can be found on the sticker on the back of the console.
If the date is newer than the one on the left but older than the one on the right, it's probably the right one.
Also check your power supply voltage (on the label above the power socket hole) matches, especially on Slims!
Slim E Consoles:
Consoles with a MFR date of 06-2014 and BEFORE are likely to be Corona
Consoles with a MFR date of 07-2014 and AFTER are likely to be a Winchester motherboard.
The only way to know for absolutely 100% certain is to open up the console and remove the heatsink and take a look at the XCGPU.
In the Corona consoles they still have an IHS (integrated heat sink) an on the Winchester motherboards they do not.
If your XCGPU looks like below, it is a Winchester and CANNOT be modified!
You need to check the NAND first to ensure what steps you need to take to RGH 3.0 your Corona.
Once you verify your NAND Type, check for POST_OUT and ensure that you can read and write, then follow the steps in the NAND Reading section.
POST_OUT Identification: Check near point STP501.
If you can see the traces (left image), you DO NOT need a POST FIX adapter.
If you have no traces (right image), you NEED a POST FIX adapter.
Required Items
Xbox 360 Opening Tool (Recommended, but not required)
A NAND Reader: LPT (Slowest), NAND-X or JR-Programmer (Better), or XFlasher (Best)
Approx 50CM 28AWG or thinner wire
ALL Phats:
1x 1n4148 (or similar) Diode.
1x 22k Resistor: (Brown, Black, Orange, Yellow)
Resistor:
Trinity: 1x 3k-10k Resistor: (Brown, Black, Orange, Gold)
Corona: 1x 1k Resistor: (Brown, Black, Red, Gold)
Corona V3/V4: Post Fix Adapter
Fine Tip Soldering Iron
A very steady hand, and experience in Soldering (Recommended)
An Xbox 360 (Duh!)
Performing RGH 3.0
Performing RGH3.0 is very simple:
1: Install your NAND Programmer Tool of choice
2: Install the appropriate wires and required Resistors/Diodes (See Required Items above) for RGH3
3: Follow J-Runner Guide (easiest!) or the legacy RGH2-3 Converter guide (harder)
Step 1: Connect your NAND Programmer of choice to your Xbox 360.
Select the chosen route below for further explanation and images.
You'll need to make an LPT Programmer.
You will need the following:
A computer with an LPT-Port (Printer port)
Soldering Iron
Soldering tin Wire
1x LPT-Plug (DB25)
5x 100 Ohm Resistors
1x 1N4148 Switching Diode (1N914 Switching Diodes will also work where 1N4148 Diodes are mentioned)
Optional: Shrink Tubing or Electrical Tape
Open the Console Type below for a Diagram on how to build and connect the Programmer to your Console.
Ignore the J-TAG Diagram part! You only need to built the SPI (LPT) Adapter.
As explained in the photo below, check the resistor pads under J2C3.
Follow as the image text explains, depending on your board version.
Unsure? See "Identifying what Corona you have" at the top of the guide.
Once you've connected your NAND Reader Wires, refer to the below images in the correct spoiler for your Console Revision
Connect each point as shown in the image.
Important: Make sure that the points are connected correctly, and be CAREFUL!
The points are extremely delicate and can easily be bridged to other points which could KILL your console!
RGH 3.0 Points:
Phat:
Recommended: Place a 10K Resistor on the PLL Point and solder your wire to the other side of the Resistor
Place a Diode on the POST point and connect your wire to the diode
Recommended: Place a 3K Resistor on the PLL Point and solder your wire to the other side of the Resistor
final install looks like this:
Zoomed in points:
Trinity PLL Point
Other end of PLL Wire goes to the small point near C5R54.
You need to scrape away the coating to expose the trace on the board first.
THIS MUST BE DONE GENTLY OR YOU WILL DAMAGE THE BOARD!
If you are trying a Corona V3 or V4, you NEED A POST FIX ADAPTER!
Recommended: Place a 3K Resistor on the PLL Point and solder your wire to the other side of the Resistor
Once you're certain the points are connected properly, and your NAND Reader is installed, it's time to finish up!
Connect your console power supply and your NAND Programmer
Follow the steps in the below spoiler to build and flash your RGH3 NAND.
There are 2 methods:
1: The Easy way using J-Runner with Extras (now recommended)
2: The harder legacy way with J-Runner and the RGH2 to RGH3 NAND Converter tool.
If you're interested in the older way, I have left this in the second spoiler.
In both methods, you need to download the latest version of J-Runner with Extras.
If you already have J-Runner with Extras, it will update automatically. If not, follow the link to Octal's Thread below.
Step 1:
Connect your NAND Reader to your Xbox, and to your PC. Connect the power supply of the Xbox.
DO NOT TURN ON YOUR XBOX 360 WHILST THE NAND PROGRAMMER IS CONNECTED. YOU MAY KILL THE CONSOLE AND OR YOUR PROGRAMMER.
Open J-Runner with Extras. It should automatically detect your NAND Reader of choice and display your console type under the "Console Type" box in the upper right.
If it doesn't, Press the ? Button to make sure your Programmer can see your console properly.
If you don't get a result, check your programmer wires before continuing!
Read 2 copies of the existing NAND by pressing the "Read NAND" button, waiting for it to finish, then Read NAND again.
Now that you've backed up your Retail NAND, you need to grab your CPU Key.
We do this by Flashing Xell Reloaded to the console by:
Ensure the Console Type shows your console type, Select "Glitch2", then tick the RGH3 Tickbox, like shown below.
Press "Write ECC" and wait for it to finish.
(If the MHZ Option shows with the drop down, try 10 first. If this boots slowly or does not boot, try 27.)
Disconnect your NAND Programmer from the console and press the Eject Button to boot your console into XELL Reloaded.
If all went well with your RGH 3.0 Install, you should now see XELL Reloaded on your screen.
This should only take up to 2 minutes. If it takes longer than 60 seconds on average, try an alternative timing file first as explained above.
No boot still?
CHECK YOUR WIRING!
Once the console boots into XELL Reloaded:
Note down your CPU Key and Input this into the CPU Key section in J-Runner. You will now see your console details.
Now we will build the RGH3 NAND:
Ensure the Console Type shows your console type, Select "Glitch2", then tick the RGH3 Tickbox, like shown in the photo above.
This time, press "Create XeBuild Image" and wait for it to finish.
(If the MHZ Option shows with the drop down, try 10 first. If this boots slowly or does not boot, try 27.)
If your console does not boot on either 10/27MHZ options, change your resistor for a LOWER one (EG if you used 22k, try 10k)
J-Runner will automatically select the newly built RGH3 NAND.
If you haven't already, turn off your Xbox, reconnect the NAND Programmer, and then click the "Write NAND" button to flash the new RGH3 NAND to your console.
First, make sure you have J-Runner with Extras. You need this tool to read/write your NAND and prepare the RGH2 built nand which you'll convert later in the guide.
Links to J-Runner can be found just above these spoilers.
Also make sure you downloaded the RGH 2 to RGH3 Converter Tool, which can be found in the spoiler below:
Tool is virus free, full scan results below.
VirusTotal Scan
There are a few FALSE POSITIVES.
Please add this tool to your exceptions if it gets caught.
Step 1:
Connect your NAND Reader to your Xbox, and to your PC. Connect the power supply of the Xbox.
DO NOT TURN ON YOUR XBOX 360 WHILST THE NAND PROGRAMMER IS CONNECTED. YOU MAY KILL THE CONSOLE AND OR YOUR PROGRAMMER.
Open J-Runner with Extras. It should automatically detect your NAND Reader of choice and display your console type under the "Console Type" box in the upper right.
If it doesn't, Press the ? Button to make sure your Programmer can see your console properly.
If you don't get a result, check your programmer wires before continuing!
Read 2 copies of the existing NAND by pressing the "Read NAND" button, waiting for it to finish, then Read NAND again.
Extract the RGH3.0 tool to a folder of your preference.
Open the extracted files and open the "ECCs" Folder
Drag and drop the ECC File containing your board revision name to J-Runner's "Load Source" box and press the Write NAND button
The ECC File name depends on your console:
Corona non 4GB Models, use RGH3_Corona.bin
4GB Corona use RGH3_Corona_4G.bin
Trinity use RGH3_Trinity.bin
Phats, use the RGH3 file with your motherboard revision in:
EG: I am RGH3 installing on a Jasper, so I first use RGH3_Jasper_10mhz.bin.
If it doesn't boot instantly or takes longer times to boot, I use RGH3_Jasper_27mhz.bin
Flash this to your console by dragging and dropping it into the Load Source Box in J-Runner and pressing "Write NAND"
Next: Disconnect your NAND Programmer from the console and press the Eject Button to boot your console into XELL Reloaded.
If all went well with your RGH 3.0 Install, you should now see XELL Reloaded on your screen.
This should only take up to 2 minutes. If it takes longer than 60 seconds on average, try an alternative timing file first as explained above.
No boot? Phats try 10mhz First, then 20mhz timing.
No boot still? CHECK YOUR WIRING!
Once the console boots into XELL Reloaded:
Note down your CPU Key and Input this into the CPU Key section in J-Runner, then create a new RGH 2.0 NAND:
Select "Glitch2", Make sure "Kernel Version" is "17559", press "Create XEBuild Image".
DO NOT FLASH THE RGH2 FILE!
Now it's time to convert the RGH2 NAND to RGH3:
The new RGH3 NAND Creator Tool is by far the easiest method of converting RGH2 NANDs to RGH3.
If you get stuck, read the status message in the app.
It will tell you what you're doing wrong!
Drag and drop the RGH2 NAND File J-Runner created for you earlier
onto the "Drag and Drop your RGH2 NAND here" section
Enter your CPU Key.
(You can also copy + paste it there if easier)
Select your Xbox 360 Type.
Open the Console Type Spoiler for the next steps:
Select the your Motherboard Type
Select 10mhz first and try that.
If your console doesn't boot, or you didn't have success with Xell on 10mhz, use 27MHZ.
Select your Motherboard Type
Once the Tool finishes making your NAND, it will appear in the RGH3Tool Folder next to the EXE.
If you need to rebuild the NAND, or you want to make another NAND, press Reset to start again.
If you haven't already done so, turn off your Xbox, leave the power connected, and reconnect your NAND Programmer.
Use J-Runner to write the newly made RGH3NAND File to your Xbox by dragging the RGH3NAND.bin file to J-Runner's Load Source box as shown below, then press "Write NAND".
Once this is finished, you're done!
Use the power button as normal to attempt to boot your newly RGH3 Modified console to the Dashboard.
Make sure you disconnect the NAND Programmer first!
If you're curious, click the little "Credz" button for a neat little shrine to everyone involved in creating RGH3 and it's tools
Once this finishes, your console is now ready!
Disconnect your NAND Programmer and attempt to boot using the power button.
Within 60 seconds or so, you should boot into the Dashboard.
Most consoles will Instaboot, you may have to try different timings and or resistor values.
As long as it boots, you're free to put it back together and enjoy your new Homebrew enabled Xbox 360!
Go and grab yourself a copy of XEXMenu and DashLaunch, and have fun!
If you're having issues, double check your wiring.
If you're stuck, post a new thread in the Console Modding Support section linked at the top of this guide.
Credits/Greetz
1 15432 - RGH3.0
DrSchottky - [Click here to view this link] (Link to GitHub)
xXBeefyDjXx - RGH2 to RGH3.0 GUI
Octal450 - J-Runner with Extras
The Project Liberation Team - You know who you are
Disclaimer:
Neither I (xXBeefyDjXx) nor Se7ensins is responsible for any events that arise from following this tutorial including but not limited to:
Killing consoles, getting suspended from Xbox Live, Suffering burns/lead poisoning, fires.
For your own health and safety, make sure you use Soldering Irons in open spaces with plenty of ventilation, don't breathe in any fumes.
Do not follow this tutorial if you do not feel you have the capacity to do so. You have been warned!
Читайте также: