Aorus x470 ultra gaming горит красным vga
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
Julie2703
Hi everyone,
I just built my pc and when I I boot up the computer, there is no signal displayed onto my monitor. CPU LED stays lit for half a second then goes away, and then DRAM LED lit up few seconds and repeat. I tried single ram stick, alternating ram slot and ram stick nothing works. everything else seem working properly every fan spinning, water cooler working, VGA and ram RGP also lit, and weird thing is ram rgp light up without turning on, also the monitor worked perfectly with my laptop. Can some one please help?
my specs:
CPU: Ryzen 5 3600 6 core AM4 3.6GHz CPU with Wraith Stealth Cooler
Mobo: Gigabyte X470 Aorus Ultra Gaming Socket AM4 ATX Motherboard (rev.1)
SSD: Samsung 250GB 970 EVO Plus M.2 NVMe SSD
Ram: Corsair 16GB (2x8GB) CMW16GX4M2C3000C15 DDR4 3000MHz Vengeance Pro RGB
GPU: Gigabyte GeForce RTX 2060 Gaming 6G OC Pro Graphics Card
PSU: Corsair RM550x 550W V2 Power Supply Fully Modular 80 Plus Gold
HDD: Western Digital Blue 1TB SATA3 HDD 64M Caviar Blue WD10EZEX
It said that my mobo is ryzen 3000 ready on the website but i dont know does it need bios update to ready or it's already ready or ryzen 3000. Also i could find my ram in ram support list of the mobo. Is it a huge problem?
ProPlayerGR
Reputable
I will try to figure out which way to save money QAQ. Anyways, thank you so much for your help. I will update you if after updating my mobo, the problem solved or not.
If I were you, I would just buy a ryzen 3000 ready motherboard, to avoid all the fuss, but it's your move. Hope it works out for you!
ProPlayerGR
Reputable
Hi everyone,
I just built my pc and when I I boot up the computer, there is no signal displayed onto my monitor. CPU LED stays lit for half a second then goes away, and then DRAM LED lit up few seconds and repeat. I tried single ram stick, alternating ram slot and ram stick nothing works. everything else seem working properly every fan spinning, water cooler working, VGA and ram RGP also lit, and weird thing is ram rgp light up without turning on, also the monitor worked perfectly with my laptop. Can some one please help?
my specs:
CPU: Ryzen 5 3600 6 core AM4 3.6GHz CPU with Wraith Stealth Cooler
Mobo: Gigabyte X470 Aorus Ultra Gaming Socket AM4 ATX Motherboard (rev.1)
SSD: Samsung 250GB 970 EVO Plus M.2 NVMe SSD
Ram: Corsair 16GB (2x8GB) CMW16GX4M2C3000C15 DDR4 3000MHz Vengeance Pro RGB
GPU: Gigabyte GeForce RTX 2060 Gaming 6G OC Pro Graphics Card
PSU: Corsair RM550x 550W V2 Power Supply Fully Modular 80 Plus Gold
HDD: Western Digital Blue 1TB SATA3 HDD 64M Caviar Blue WD10EZEX
It said that my mobo is ryzen 3000 ready on the website but i dont know does it need bios update to ready or it's already ready or ryzen 3000. Also i could find my ram in ram support list of the mobo. Is it a huge problem?
To be sure that your mobo is ryzen 3000 ready it must say it on the mobo's box, on the front. Also, check if you have connected your monitor to your gpu.
Решил обновить древний ПК, оставив от старого видеокарту (msi geforce gtx 650 ti boost) и блок питания на 750 ватт. Из нового i5-10400f, материнка gigabyte b560m aorus elite. ОЗУ amd radeon r9 gaming series 2 плашки по 8гб. Все собрал, включаю - горит на материнской плате красным vga led, на мониторе нет сигнала, все вентиляторы крутятся, в том числе и на видеокарте. Перепроверил все на старом пк- все работает, и монитор и видеокарта и блок питания. Где то читал, что может быть несовместимость блока питания и материнки, но это как то странно звучит. Что делать, помогите пожалуйста
Кстати говоря, заметил, что кабель 24 пина, который идёт от блока питания к материнской плате какой-то странный, хотя где-то читал, что это норма. Отсутствует 1 пин, читал, что это -5 вольт, и этот пин не использутся лет 15, да и на старом пк все работает. Но может это поможет в решении вопроса
Садыржоп Нургожо, я не так давно на проекте, но уже сообразил: если отвечать на каждый вопрос неважно что, вплоть до ахиней, то будешь в топе и хоть сверхразумом
а батарейку cr2032 из мат-платы вынуть не разу не пробовал чтобы инициализировать видеокарту дискретную а то по умолчанию идет запуск со встройки
Можно подробнее? Я вынимал батарейку на секунд 30. Может для этого какие-то особы правила есть. Видеокарту вставить в момент извлечения батарейки?
Ярослав Перфильев Гуру (4506) Егор Роянов, вставляем видеокарту вынимаем батарейку предварительно надо обесточить полностью системный блок нажать пару раз на кнопку питания и пробовать включать нормально
да вот еще попробуй оперативку поставить так
1 планка в первое гнездо и вторая планка в третий разьем чтобы задействовать двух-канальный режим
тогда попробуй запустить с одной планкой памяти либо без видеокарты от встройки
и если запустится с одной планкой памяти значит одна планка памяти битая если же запустится без видеокарты то значит линия 12 вольт на блоке просажена и процессор новый больше потребляет и на видеокарту не хватает питания
Егор Роянов Ученик (104) Ярослав Перфильев, так как он без видюхи запуститься, у меня версия процессора 10400f, он без встроенной графики
скорее всего в блоке у тебя одна линия 12 вольт разделена проводами без шим всяких отсюда и затык нехватка по линии 12 вольт из за того что у нового процессора потребление по выше идет просадка по линии 12 вольт отсюда не хватает видеокарте на запуск
Вряд-ли материнская плата gigabyte b560m aorus elite синего цвета.
Но ответ всё равно есть.
В большинстве случаев монитор может не работать из-за оперативной памяти, может быть контакты забиты и т. д.
А на счёт несовместимости.
Почти у всех блоков питания 24пин может делится на 20+4пин (отдельно 20пин и ещё 4пин можно присоединить на материнки больше контактов)
Если вентиляторы, кулеры работают, то, блок питания исправен.
А то что на твоём фото о контакте блока питания - то оно обязано так быть.
Это фото еще до покупки, старая плата, просто фотал кабель. Новая черная). Просто я обе плашки опробовал по отдельности, не мог же быть брак сразу на двух
Антон Кукасов Мастер (1027) Егор Роянов, оперативная память не может быть из коробки бракованная быть, только если не отработать твоё 10-ти летний ресурс. Ну если всё новое, а пыль не успела забить контакты, то, попробуй запустить без видеокарты. А. А ещё есть иногда такая проблема, то что биус старый и не может быть совместимо с процессором, если ты покупал в DNS, то должен был перепрошить на UEFI.
I just got my board and have assembled it. The computer makes 1 long beep and 3 short beeps after regardless if it is connected via mobo HDMI or not. The VGA LED stays on red. There is no GPU installed just the bare mother board with CPU/CPU fan. I have checked all wires multiple times. I thought initially the error was due to improper monitor (I tried using my LCD TV). So I bought a dedicated computer monitor with HDMI. I still have this problem.
Can anyone help?
Setup:
X470 mobo ,
AMD Ryzen 7 2700x,
G.Skill RipJaws V series 16GB DDR4-3200MHz intel Z170 memory,
Seasonic X-650 Gold PSU.
you dont have a gpu! You bought a cpu without an igpu, and didnt install a dedicated gpu. You need a gpu. The outputs on the motherboard are to support the cpu's that have a gpu built in such as the 2400G
My Signature.
I do not work for gigabyte. My advice and opinions are my own.
Firstly, thank you thank you for your reply.
I failed to comment that I have connected a GTX 550ti to it. And still I get the same error. I am not sure what I am missing. Is it a header pin issue of some sort? What ever scenerio with GPU, without GPU I get the same error.
I rewired everything and tried by graphics card Nvidia GTX 550 Ti. The error code has gone but I still get no video output. I will post more updates as I progress.
with older graphics cards you have to enable csm in order to get a display. Not sure about amd cards, but on the nvidia side I think its anything around the 750ti or older requires csm to be enabled. some of the 750 cards had uefi from the factory, but most came with a legacy bios. anything older than that would have come with a legacy bios and wont work on a uefi motherboard without csm enabled.
My Signature.
I do not work for gigabyte. My advice and opinions are my own.
Isn't CSM enabled by default? Do you have the monitor plugged into the video card and not into the HDMI port on the motherboard?
My Signature.
Syaoran
Ryzen 2700X @ 4GHz
Arctic Cooling Freezer 360
MSI MAG X570 Tomahawk WiFi
64GB (4X16GB) Crucial Ballastix RGB PC4-3600 C16
Powercolor Red Dragon Vega 56 8GB
2X Sabrent Rocket 500GB NVMe M.2 2280
Seagate 6TB SATA 3/7,200RPM/256MB Cache
Seagate 4TB SATA 3/7,200RPM/128MB Cache
Seagate 4TB SATA 3/7,200RPM/128MB Cache
Silverstone Strider 1200 Gold
Phantek Enthoo Primo SE (Green)
On my z170 board it is was not enabled by default when I got the board. My old gtx470 would not display anything. I had to use the igpu to enable it and get the 470 working. I had an rx480 on the way, but needed something to use in the meantime. I actually have 2 gtx470's that I had been running in sli on my previous build and one of them I have never been able to get it to display anything when running on my 1151 board. Not sure why it wont display but it still works fine in my old core 2 quad system. I can run both cards in sli without trouble but it only display through my non reference zotac card, the reference asus refuses to display.
My Signature.
I do not work for gigabyte. My advice and opinions are my own.
UPDATE: I was able to get my VGA working. I installed an old GTX 550ti GPU and used a DVI to HDMI adaptor. Working great with TV. Now if I can get the damn M2 slots to work. I followed instructions but the card I have only fits in the M2B slot. I am assuming that matters?
I actually called support the day I bought my board to ask about the M.2_B slot. I didn't want my 960 EVO under my video card but didn't want to lose performance in a slower slot. Both M.2 slots on the Gaming 7 WiFi are full speed x4 slots.
My Signature.
Syaoran
Ryzen 2700X @ 4GHz
Arctic Cooling Freezer 360
MSI MAG X570 Tomahawk WiFi
64GB (4X16GB) Crucial Ballastix RGB PC4-3600 C16
Powercolor Red Dragon Vega 56 8GB
2X Sabrent Rocket 500GB NVMe M.2 2280
Seagate 6TB SATA 3/7,200RPM/256MB Cache
Seagate 4TB SATA 3/7,200RPM/128MB Cache
Seagate 4TB SATA 3/7,200RPM/128MB Cache
Silverstone Strider 1200 Gold
Phantek Enthoo Primo SE (Green)
I have the same issue, during boot the VGA LED stays on! And no output on the HDMI port.
My setup:
X470 Aorus Ultra Gaming
AMD Ryzen 7 3700 WRAITH
Corsair 32 GB 3200 RGB PRO
GIGABYTE RX5700 XT
CoolMaster 750W ATX23
AORUS M.2 SSD 512 GB
Seagate BarraCuda 2 TB HDD
I just finished the assembly of my board. The MOBO starts and controlles CPU fan, casing fans and all RBG (all same colour controlled by VBG). No beeps can be heard (speaker is connected).
I tried different HDMI cables, no succes.
Checked CPU for pin damage/bend. CPU looks perfect.
Tried a bare MOBO with only RAM and CPU/FAN installed. No succes, the LED of VGA is still active!
Checked wires multiple times, no visual damage or pins bend.
Also tried to use the external GPU, no output on all 4 connectors.
Did you update the bios on the motherboard? The x470 wont POST without the bios having been updated to a bios that supports the 3700 before the cpu was installed.
My Signature.
I do not work for gigabyte. My advice and opinions are my own.
Thank you for your fast reply!
No I wasn't able to preform an update of the BIOS because I didn't get any screen output. Or is there another way to preform a update without the use of a screen?
Some how i managed to get a screen output, don't ask me how ;p
I can see the BIOS Version is F41, according to the support website this is the second most recent version.
Do you think its necessary to update the BIOS to F42a??
Have the same issue GPU red led on, beeps two times then four times, no boot.
First time I switched slots for rams 2x8gb corsair lpx and it started somehow.
Second time I used an older video card 250 gts, pffft, to boot then shut down, put current used rx 580 and it started.
After the second time I updated bios to F50 even though I have a 2000 series amd processor.
Few months had no issue.
Third time, a power outage, did everything I could, does not want to start, same red gpu led on, just stays on and does nothing.
Where is the back up bios? It doesn't have dual, marketing bs, the second bios is a back-up bios in case it doesn't start with the main one. Guess what, it doesn't start. Don't care why not, don't care about all the chit chat techicalities I work in IT and in all my 20 years of experience I haven't seen a mobo in this price range to be so picky, unreliable and faulty, for whatever reason. Don't even care about the reason, I gave it everything, yes tested different brand rams and yes without xmp profile, yes ps in gold seasonic with more than enough power, yes good proc, yes updated bios, yes verified rams, and still is BLOCKED IN A BIOS LOOP. There is no hardware issue here it's about the pickyness of the mobo and the "somehow" you manage to get the mobo out of her loop.
It is obvious that it has bios read/write issues after any "whatever" it doesn't like it.
You have to make her forget it is stuck in that loop, thats why you can pull the video card out, even the ssd m.2, hdd and still get the red gpu led.
Yesterday I took courage and used DualBios Rescue.exe.
Damage didn't make them, he made 2 passes (1 quick and 1 quite slow), he finally restarted the PC and I had no problems.
I disconnected the power supply, situation for which you had the problem cpu led blink with dram led (M_bios), and to my astonishment the PC has restarted correctly.
Now I don't know if I really recovered the M_bios, in the next few days I'll let you know.
For the moment I am satisfied
My Signature.
PC : Win10Pro 64 bit - Tt Versa C21 Rgb - Gb X470 Aorus Ultra Gaming (F50) - Ryzen2700x + CM ML240L RGB - Tt SmartPro RGB 750W 80+Bronze - G.Skill 32GB -F4-3200C16-16GIS - GB GTX 1050 Ti WindForce X2 OC - M.2 Samsung SSD 970 EVO 500GB - Crucial P1 1TB - HD 4Tb ST4000DM004 - LG BH10LS30 - XL2370HD Modem/Rooter : DGA4132 (AGTHP)2.1 - 1GB/100MB
How did you solve it? my x470 ultra gaming every time I disconnect the psu when starting the system it takes 5 minutes and then the bios restarts and I have to load my configuration again
My Signature.
PC : Win10Pro 64 bit - Tt Versa C21 Rgb - Gb X470 Aorus Ultra Gaming (F50) - Ryzen2700x + CM ML240L RGB - Tt SmartPro RGB 750W 80+Bronze - G.Skill 32GB -F4-3200C16-16GIS - GB GTX 1050 Ti WindForce X2 OC - M.2 Samsung SSD 970 EVO 500GB - Crucial P1 1TB - HD 4Tb ST4000DM004 - LG BH10LS30 - XL2370HD Modem/Rooter : DGA4132 (AGTHP)2.1 - 1GB/100MB
I have the solution:
For those who have problems with mb gigabyte (in my case x470 aorus ultra gaming) as in the video, with m_bios stuck in this situation and that start only forcing the start from the backup one and that every time they switch off the power they find you again with the problem (but without physical selection of boot between main and backup bios), maybe there is a solution. For now it has worked for me and at least 2 other users.
I take no responsibility, so it is at your own risk.
I solved. In theory it should overwrite the m_bios with the b_bios, in my case fully functional and updated to the F31.
Another italian user with b450 with same problem has solved, also rojasjonatan9 has solved similar problem.
I started it right button run as administrator.
Once installed and started, he did 2 steps, the first one quite fast, I think it was the reading of the bios, the second a little slower in theory the rewriting of the main bios, at the end of the second phase it restarted by itself after 5 seconds.
I hope it can help others
My Signature.
PC : Win10Pro 64 bit - Tt Versa C21 Rgb - Gb X470 Aorus Ultra Gaming (F50) - Ryzen2700x + CM ML240L RGB - Tt SmartPro RGB 750W 80+Bronze - G.Skill 32GB -F4-3200C16-16GIS - GB GTX 1050 Ti WindForce X2 OC - M.2 Samsung SSD 970 EVO 500GB - Crucial P1 1TB - HD 4Tb ST4000DM004 - LG BH10LS30 - XL2370HD Modem/Rooter : DGA4132 (AGTHP)2.1 - 1GB/100MB
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
malkybutt
Hello guys, I am in dire need of help before I go crazy.
I have built a new rig and the BIOS doesn't post. The DRAM and CPU LEDs alternate and I have tried all the possible solutions I have found online with no avail. I have RMA'd everything but the e-shop said everything is fine yet it is not. If things won't improve I'll probably ask for a mobo replacement cause it must be it.
Mobo: AORUS ULTRA GAMING x470
RAM: F4-3000C16D-16GTZR
CPU: Ryzen 2600x
PSU: Corsair (TX650M)
GPU: GTX 660TI (while getting money for a new one)
SSD: Samsung 970 EVO
Thank you beforehand for all the replies and help.
jojesa
Glorious
The RAM F4-3000C16D-16GTZR is listed but it appears as an 8GB stick, instead of a 16GB kit. It appears Gigabyte made a mistake since on G.SKILL website that ram is listed only for Intel motherboards.
Also on the G.SKIL RAM Configurator the F4-3000C16D-16GTZR does not appear as been compatible with any AMD AM4 platform.
If you power on without any RAM installed, does the RAM and CPU LEDs behave the same way?
I would try another RAM or contact G.SKILL
jojesa
Glorious
You should have posted what you have tried already.
malkybutt
You should have posted what you have tried already.
My bad, I did tried all of that but shoudl have mentioned it.
But yea I tried to:
Reset CMOS
Breadboard it with just a single ram
All standoffs were already placed in the case by the manufacturer
All ATX connectors were plugged and seated properly
Ram were seated in dual channel in slot 1 and 2 according to the manual.
bmockeg
Honorable
malkybutt
bmockeg
Honorable
malkybutt
Don't need to be rude or passive aggressive you know. The 2600x is a Pinnacle Ridge CPU and that Gskill memory is listed as supported.
jojesa
Glorious
The RAM F4-3000C16D-16GTZR is listed but it appears as an 8GB stick, instead of a 16GB kit. It appears Gigabyte made a mistake since on G.SKILL website that ram is listed only for Intel motherboards.
Also on the G.SKIL RAM Configurator the F4-3000C16D-16GTZR does not appear as been compatible with any AMD AM4 platform.
If you power on without any RAM installed, does the RAM and CPU LEDs behave the same way?
I would try another RAM or contact G.SKILL
malkybutt
The RAM F4-3000C16D-16GTZR is listed but it appears as an 8GB stick, instead of a 16GB kit. It appears ASUS made a mistake since on G.SKILL website that ram is listed only for Intel motherboards.
Also on the G.SKIL RAM Configurator the F4-3000C16D-16GTZR does not appear as been compatibel with any AMD AM4 platform.
If you power on without any RAM installed, does the RAM and CPU LEDs behave the same way?
I would try another RAM or contact G.SKILL
I will contact GSKILL and will let you know. I am just very annoyed to see that GIGABYTE lists it as compatible (I literally copy-pasted the product code before buying it) while GSKILL does not. It's infuriating.
Thanks for the answer. Let's hope for the best.
malkybutt
The RAM F4-3000C16D-16GTZR is listed but it appears as an 8GB stick, instead of a 16GB kit. It appears Gigabyte made a mistake since on G.SKILL website that ram is listed only for Intel motherboards.
Also on the G.SKIL RAM Configurator the F4-3000C16D-16GTZR does not appear as been compatible with any AMD AM4 platform.
If you power on without any RAM installed, does the RAM and CPU LEDs behave the same way?
I would try another RAM or contact G.SKILL
I contacted G.Skill and they gave me a list of compatible DRAMs, saying that indeed the list on Gigabyte's site is wrong and they made a mistake. I have returned the RAM and bought the correct one, hopefully, the nightmare is over.
Thanks for the help man. I still can't believe Gigabyte made such mistake, sigh.
Читайте также: