Bios not installed что делать
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
HextechNades
Got a brand new motherboard, everything turns on but i cannot get it to detect any harddrives. It wont detect my old harddrives or my new one that i just got today. Everything is connected correctly, all new sata cables that came with the new motherboard. Ive tried using different sata slots. Ive tried messing around in the bios everywhere and i cannot get my harddrives to detect.
- Samsung 860 EVO SSD 500GB (New one i just bought)
- Western Digital Caviar Blue 1TB 3.5'' 7200 RPM
- Kingston a400 240GB 2.5'' SSD
HextechNades
I fixed the issue. The problem was the sata ports in my power supply were not functional. So my harddrives werent getting any power. Fortunately i had an extra power supply.
rgd1101
RealBeast
Titan
Check the motherboard support site QVL, Corsair Vengeance LPX (CMK16GX4M2B3200C16) is not compatible (with almost any B450 board). Check with Corsair support for recommended settings or exchange. The CMK16GX4M2B3600C18 is though.
HextechNades
Check the motherboard support site QVL, Corsair Vengeance LPX (CMK16GX4M2B3200C16) is not compatible (with almost any B450 board). Check with Corsair support for recommended settings or exchange. The CMK16GX4M2B3600C18 is though.
mine is CMK16GX4M2A2400C16, DDr4 16GB(2x8), 2400mz 16-16-16-39, 1.20V, ver 5.30
Also Yeah, ive been trying to install windows and each time it cant find a harddrive to download it on, and like i said ive put in a brand new, fresh, clean harddrive and that wouldnt even register. And my bios isnt detecting any of my harddrives either. So i basically cannot get into the computer. It just loads in windows and if i take the usb out to download windows, it just puts me straight to the bios and i cant really do anything.
С недавнего времени комп начал пищать 3 раза при полном входе в Windows (когда уже надо пароль ввести) и при выключении (когда появляется надпись "Завершение работы").
Я подумал, что это все ОС как всегда виновата.. .
Затем комп стал зависать: не реагирует не на что, кроме перезагрузки (кнопочка такая:)) , если играла музыка, то она превращается в писк.. .
Стал смотреть и заметил при врублении ПК ошибку в биосе.. .
Serial ATA AHCI BIOS, Version iScr 1.20E
Copyright (c) 2003-2008 Intel Corporation
** This version supports only Hard Disk and CDROM drivers **
Please wait. This will take few seconds.
Провел обнуление БИОСа - не помогло.. .
Объясните причину всего этого.
Ну я не хочу чтоб мой новый комп заглох, как и некоторые его Б/У предшественники.. .
Помогите, кто знает! Буду очень признателен! Заранее спасибо)
Сами вы - дебил. Я никуда не лазил, а сам - компьютерщик, поэтому меня очень это удивило) Хотя более на железе спец и настройке, а ошибки - не мое.
Алексей, я не мега про.. .
Я лишь любитель, учащийся на своих же ошибках и ошибках моего ПК + иногда читаю всякие умные книжечки про комп) .
Помогаю знакомым только и себе комп ремонтирую.
это не ошибка биос! видел вчера такое на работе - у клиентов была отключена звуковая карта в диспетчере устройств и вот таким образом windows издавала сигналы приветствия. копайте в сторону звуковой карты, её драйвера и так далее.
КОМП сигналами писка до полной загрузки сообщает свое состояние. Если возникает неисправность и комп не может загрузиться он пищит и по количеству писков можно определить, что не сработало. Так, что не переживай и биос у тебя грузится правильно и те надписи, что привел не ошибки. Если стал подвисать, то причиной мошуть быть антивируус, его настройка и пропущенные вирусы. Проверь программой Anti-Malware.v1.61.0.1400.keygen-FFF.RED
ну ты же спец-глянь в биосе вкл ли AHCI или у тебя Standart IDE стоит. . так же возможно вирус в мбр-дрвеб кюрейт в помощь, мбр проверит сразу при запуске проверки С: \.
на дефолт я так понял уже сбрасывал. есть возможность биос перепрошить? проблема видимо в нём. зайди на сайт производителя плат, там есть последние версии биоса. 3 гудка- ошибка DMA ещё батарейка может лажать.
Здравствуйте. Пр загрузке пк вылезает ошибка из названии темы на 1-2 секунды, потом вылазит надпись very pool data( или как-то так) и погасает моник,потом включается и черный экран. Винда не грузится. Как это побороть? 5 минут назад ставил загрузку с сд-рома в биосе. Потом обратно с харда и такая трабла. Модель материнки FOXCOON( пишу только название фирмы точно модели незнаю).ОС виндовс хр
XMS Driver not installed.
XMS Driver not installed или неудачная прошивка BIOS'a. Шил из под доса с помощю AWD862.exe (для.
installed boot media
Здраствуйте, если тема здесь не подходит просьба модераторам перенести в нужный раздел. У моей.
The language server needs at least php 7 installed
Здравствуйте, возникла проблема, при работе с языком PHP в VS Code с ошибкой о необходимости.
в биосе поставь IDE заместо AHCI
Добавлено через 29 секунд
черт я опоздал =)
Да не переживай что ты опоздал. Я сам вчера смотрел, там изначально стоит IDE. Пробовал менять на AHCI и обратно и всё равно эффекта 0
Попробуй загрузись с лайв образа и посмотри что творится с жестким диском. а заодно попробуй дровишки подтянуть на AHCI.
а теперь я первый =)
A 333MHz system bus processor is installed
Здравствуйте! Такая проблема. Материнка "ECS G33T-M2"; Процессор "DualCore Intel Core 2 Duo.
Epson stylus CX4100 The driver cannot be installed
Пытаюсь установить драйвер на винде 7 х86 от этого принтера. Подключаю его к компу, включаю.
BIOS. cd-rom boot priority not installed
При установке windows не удается загрузить образ операционной системы с диска. Биос не видит диск.
SQL Server 2000 is not installed on this machine
MS SQL Server 2000 на XP SP3 работает ребиата , я установил всиё 4 exe File и у мения пишет.
Проблема с драйвером АДО: driver not correctly installed
привет всем! У меня возникла проблема с драйвером адо говорит что-то типа этого: driver not.
Windows did not detect a properly installed network adapter
Не могу заинтернетится в связи"Windows did not detect a properly installed network adapter". и.
Hi:
I am working with a NetServer LT6000r, I have a problem when it starts, It shows me the following message: "Bios Not Installed", I dont know exactly what does it mean?, so, i Tried to start from a Windows NT 4.0 CD, but I couldn't, (when the cd tries to start a blue screen is showned) and the server down.
Whay can I do?
some suggestions?
- Mark as New
- Bookmark
- Subscribe
- Mute
01-19-2006 10:08 AM
01-19-2006 10:08 AM
First, the "BIOS Not Installed" Message:
This is not an error, but a normal condition of the server if there is no boot drives connected to the SCSI Controller. No reason to be concerned.
Next, the booting issue: Is there an operating system installed or are you trying to install one? If it is a clean install, have you configured your RAID Array and initialized it?
Post your configuration here so we can help you make sure everything is setup.
If you are installing Windows NT Server 4.0, use the 3-floppy setup method otherwise you may not be able to load a driver for the CD-ROM. You will also need the driver for the integrated RAID Controller. It is O/S specific so let us know what you are installing.
Get back to us with the above information ane we will walk you through it step-by-step.
Sean T. Craig Sr. C.E.T., M.C.P.
- Mark as New
- Bookmark
- Subscribe
- Mute
01-19-2006 03:18 PM
01-19-2006 03:18 PM
Hi Jose,
It's not a problem.. It is a message saying no scsi bootable disk found on purticular scsi controller. Normally this message will come for the scsi channel, where you connect cdrom & DAT drive.
If you want to install any OS, you have to use netserver navigator cd, & follow the step by step operation. Also you should create the driver disks required for your server from navigator cd..
- Mark as New
- Bookmark
- Subscribe
- Mute
01-20-2006 06:05 AM
01-20-2006 06:05 AM
Hi, the message exactly is:
.
.
for Configuration Utility
to pause Configuration message
No Logical Drives Found
BIOS Not Installed!
.
.
.
.
finally is showed:
Operating system not found
The configuration I am using is:
1 NetServer LT6000r HP
4 processors 700Mhz
2 HD 9Gb RAID 0
2 STORAGE/12 with 7HD of 36GB
thanks for your help.
- Mark as New
- Bookmark
- Subscribe
- Mute
01-20-2006 06:49 AM
01-20-2006 06:49 AM
In regards to Shameer's response, if you have a Navigator CD, that's fine but it is not required, nor does HP still recommend it since all the drivers on it are antiquated.
If you are getting "No Logical Drives Found", you need to go into the NetRAID Utility using M at startup and configure the array(s).
Again, if you are trying to do a clean install of Windows NT 4.0, create the boot floppies so that you can load the CDROM driver. You don't need it at the DOS level but as soon as you try to boot to a GUI, it will fail to read the CD.
The same thing goes for the NetRAID Driver. Download it and extract it to a diskette. When the setup starts, press to specify 3rd party mass storage drivers. Then specify it again and scroll "UP" to the ATAPI IDE CDROM and select it.
Sean T. Craig Sr. C.E.T., M.C.P.
- Mark as New
- Bookmark
- Subscribe
- Mute
01-20-2006 08:18 AM
01-20-2006 08:18 AM
Hi, friends:
I did it , but in the option CONFIGURE - EASY CONFIGURATION or NEW CONFIGURATION, when I select with the menu at the bottom "SPACE-SEL" I get a window showing "DRIVES NOT RESPONDING CANNOT BE SELECTED. PRESS ANY KEY TO CONTINUE".
And when I select "F3", It doesn't show me nothing( I mean, a window with "no logical Drives Configure").So I can't configure the array.
Why I can not see the array?
Actually, the problem began when the server crashes suddenly, and show the message that I wrote before, so I decided to configure it again, but I could not.
- Mark as New
- Bookmark
- Subscribe
- Mute
01-21-2006 03:07 AM
01-21-2006 03:07 AM
Because there are only about a hundred things that could be the problem here, we need to know ALL the configuration details, otherwise it will take us a month of writing back and forth to figure it out.
You say you have 2 internal hard drives and 2 external Rackstorage-12's. That will require 3 channels and the embedded RAID controller only has 2. Therefore, we need to know which controller(s) are in use for which devices.
Do you have both rackstorage units connected to the embedded RAID and the internal drives connected to the Embedded SCSI?
Do you have a PCI RAID Card with 3 channels and all 3 in use?
Are your internal hard drives connected to the embedded controller and the RS12's connected to a PCI controller?
All this info is extremely important in diagnosing this issue.
Have you tried clearing the CMOS? If so, could that be the cause? If your boot drives are connected to a PCI RAID card and you reset your CMOS, it may be trying to boot from the embedded controller.
The first thing you need to do, is disconnect the Rackstorage-12's from the server. Then go into M and choose Objects-->Physical Drives and see if any of the drives ARE responding. Record which drives are on which SCSI ID's and Channels and post them here; i.e.
Ch0
ID0 - A0-0 - FAIL
ID1 - A1-0 - FAIL
Ch1
ID0 - A2-0 - FAIL
ID1 - A2-1 - FAIL
etc.
If you highlight each drive and press it will show you the properties of the drives if they are responding. With the Rackstorage 12 disconnected, your 2 internal drives will be the only ones responding. If they are responding, make sure they show capacity (8677MB) and check for Media Errors and Other Errors.
I would really like to help you fix this problem but I'm not going to spend a lot of time posting guesses. Make a commitment to resolving this issue and we will too.
Знакомый купил новый компутер. Принёс домой, включил и увидел на мониторе "BIOS not installed"// "Вашу мать" - подумал знакомый и начал думать в сторону исправления сие. Но не вышло =). И так, ув. знатоки, вопрос: что делать? и что это вообще за нахер. документация к маме была изучена, но ничего дельного не нашли, какая мать я не знаю).. зарание спасибо.
Ну клево. Какая мать не знаю.
В я не знаю при чем тут линукс.
И новые компы можно и обратно относить.
Попробуй вынуть и вставить назад батерейку на мамке на часок. Потом включи, есль не поможет нужно с дубином пойти в ту фирму и рассказать им политику партии;-)
Гугль сказал, что проблема может быть с SATA диском. Мать Asus какая-то..).
Фак! я был дезинформирован. оказывается, что комп сначала грузится потом говорит subj., а потом загрузка продолжается.. и даже ОСь включается..
Это как? Основная задача BIOS загрузить ядро в память и передать ему управление. А тут прям мистика какая-то. Или чья-то плохая шутка?
Блин, спецынах. морочите тут людям головы.
Это, скорее всего, SATA-RAID какой-нть недобиос.
Ось грузится? Грузится. Тема закрыта.
Точно, включенный контроллер SATA или SCSI, когда ничего в него не воткнуто. Можно отключить.
установил флопик а комп его не видит как настроить его в биусе?
люди добрые помогите настроить флопик в биусе заранее спасибо
Проверь правильно ли установил: воткнул ли шлейф, правильно ли его воткнул, подключил ли питание, правильно ли его подключил, почитав эту самую документацию на эту самую плату Ацусь. Если все согласно документации и все исправно, ищи в "биусе" что-нибудь типа: FDD Enabled/Disabled. И позови наконец какого-нибудь типа гуру, хотя бы соседского студента. А то сам такого наподключаешь, мама не горюй.
Читайте также: